Eaton Matrix Telecom Inverter System Скачать руководство пользователя страница 27

Страница: 27 / 86

Installation

IPN 997-00012-68D February 2010

If a static transfer switch (STS) or a maintenance bypass switch (MBS) is
fitted, then go to 4.

If no static transfer switch (STS) or a maintenance bypass switch (MBS) is
fitted:

•

Refer to the Wire Size Tables on page

and local wiring rules, and

select the correct size ac cable.

•

Terminate the cables with M4 crimp lugs.

•

Route the cables to the ac neutral, ground and line terminal studs
through the left-side panel.

Secure the connections with the screws and washers supplied. Tighten the
screws according to the Standard Torque Settings on page

Step 6 - Connect ac output cables (if required)

Ignore this Step if a static transfer switch (STS) or a maintenance bypass switch
(MBS) is fitted.

Refer to the Wire Size Tables on page

and local wiring rules, and select

the correct size ac cable.

Terminate the cables with M4 crimp lugs.

Route the cables to the ac neutral, ground and line terminal studs through
the left-side panel.

Secure the connections with the screws and washers supplied. Tighten the
screws according to the Standard Torque Settings on page

not

connect the other end of cables to ac load equipment at this stage.

Step 7 - Connect inverter alarm (if required)

CN11 on the inverter shelf backplane is the inverter alarm. It will send out

alarm signal if either inverter in the shelf fails.

This alarm is typically used if the inverters are stand-alone (no controller).

If required, connect from CN11 to a suitable digital input of an external alarm
monitoring system. See details on page

Procedure complete

Task 6 - Connect Controller (if used)

CAUTION

: Ensure all the power sources are OFF during wiring. Disconnect battery cables

from battery.

Step 1 - Remove controller rear cover

Содержание Matrix Telecom Inverter System















































































Результаты поиска

Содержание Matrix Telecom Inverter System

Отзывы:

Похожие инструкции для Matrix Telecom Inverter System

Бренды по названию

Популярные бренды

Eaton Matrix Telecom Inverter System, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Matrix Telecom Inverter System

Отзывы:

Похожие инструкции для Matrix Telecom Inverter System

Бренды по названию

Популярные бренды