Eaton Matrix Telecom Inverter System Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 86

background image

Specifications

Copyright © 2008-2010 Eaton Corporation. All Rights Reserved.

IPN 997-00012-68D February 2010

57

Inverter Alarm Interface

CN11 on the inverter shelf backplane is the inverter alarm. It will send out alarm signal if either
inverter in the shelf fails.
This alarm is typically used if the inverters are stand-alone (no controller). It can be connected
to a suitable digital input of an external alarm monitoring system.

Inverter 1

Inverter 2

Status between Pin 1& Pin 2

Normal Normal

High

impedance

Fault Normal

Low

impedance

Normal Fault Low

impedance

Fault Fault

Low

impedance

«
...
61
62
63
64
65
...
»

Содержание Matrix Telecom Inverter System























































































Отзывы:

Нет отзывов

Похожие инструкции для Matrix Telecom Inverter System

Бренд: Konig Страницы: 30

Бренд: K&S BASIC Страницы: 17

Бренд: Green Power Страницы: 21

Бренд: Helvest Страницы: 2

Бренд: ADS Technologies Страницы: 1

Бренд: KAMEHA Страницы: 12

SITE INVERTER 300

Бренд: ICT Страницы: 8

B+B SmartWorx 485USB9F-2W

Бренд: Advantech Страницы: 2

Бренд: DeLOCK Страницы: 2

exacqVision E Series

Бренд: Exacq Страницы: 70

Бренд: Sarowin Страницы: 6

Бренд: NANOTEC Страницы: 22

Бренд: Seneca Страницы: 4

DA1-34072FB-B20C

Бренд: Eaton Страницы: 16

Бренд: Accorroni Страницы: 44

Бренд: Innova Страницы: 20

Бренд: Lika Страницы: 104

PWRIG100012120S

Бренд: AIMS Power Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды