Eaton Matrix Telecom Inverter System Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 86

background image

Matrix Telecom Inverter System

44

Copyright © 2008-2010 Eaton Corporation. All Rights Reserved.

IPN 997-00012-68D February 2010

LED LED

Signal

Status

1) The DC input voltage polarity is
reverse.
2) Inverter output Short circuit.
When short circuit happens, inverter
will shut down. Manual restart is
required.
3) Abnormal output voltage. The
inverter will shut down when
output voltage is out of operating
voltage range. It cannot restart
automatically.
4) Negative Power Protection. The
inverter will shut down. It cannot
restart automatically.
5) Overload fault. When the time of
overload protection exceeds the
defined time, the inverter will shut
down. Then inverter should be
manually restarted.

Note :
Power On: When inverter is in “Power On” mode, the green LED and the yellow LED are
flickering synchronously without any alarm which needs the yellow LED to indicate.
Overload and overload fault:
When overload fault alarm occurred, the yellow LED and red LED turn on at the same time
while overload alarm occurred, only the yellow LED turns on.
Priority:
If more than one warning exists at the same time, then the LED will display the highest priority.

«
...
48
49
50
51
52
...
»

Содержание Matrix Telecom Inverter System























































































Отзывы:

Нет отзывов

Похожие инструкции для Matrix Telecom Inverter System

INDUSTRIAL Series

Бренд: ICT Страницы: 2

Industrial Series VEC023

Бренд: Vector Страницы: 8

COMFOSPLIT IKARO

Бренд: Ideal Clima Страницы: 68

Бренд: CYP Страницы: 60

Бренд: Goodwe Страницы: 50

SA-1000K Series

Бренд: Samlexpower Страницы: 23

Бренд: J-Tech Digital Страницы: 5

Бренд: A-TS TECHNOLOGY Страницы: 131

Бренд: HEIDENHAIN Страницы: 36

SUNNY BOY STORAGE 3.7

Бренд: SMA Страницы: 142

Бренд: Vdwall Страницы: 23

Бренд: Omnitron Systems Technology Страницы: 1

Бренд: Omnitracs Страницы: 9

Бренд: DAB Страницы: 600

Бренд: Z3 Technology Страницы: 80

WHISPER 30 ULTRA

Бренд: Mastervolt Страницы: 32

Бренд: ELCART Страницы: 2

Бренд: Black Box Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды