background image

14

Technical Data 

 PR216-219-508-01

Effective March 2017

Installation and user manual for the  

BiWire / Conventional Repeater  

  

Installation Testing

Initial Power-up Check 

Power up the panel by engaging the fuse spur to supply mains, 

then connect the white socket of the battery cable to the power 

supply (see Figure 24 on page 16) .
Check that all indicators turn on in turn momentarily and turn off 

again .
Only the power on indicator should be lit afterwards .
Any fault indications should be investigated and corrective actions 

taken before continuing with the installation tests . “Status 

Indications” on page 8 provides a comprehensive guide to  

the fault indications . 
Power off the panel before commencing any corrective action on 

the panel . 

   WARNING

DO NOT FIX ANY FAULT CONDITIONS WITH THE SYSTEM 

STILL POWERED UP. THIS IS PARTICULARLY IMPORTANT 

WITH SHORT CIRCUIT FAULTS ON ZONES AS THE PTC 

FUSE NEEDS TIME TO RECOVER IF IT HAS TRIPPED.

Repeater Check 

• 

Place an individual zone into Zone Test Mode on the Fire 

Panel (see Fire Panel manual for further instructions on how 

to put it into Zone Test mode) . Check the following on the 

repeater panel:

• 

Self-Test On indicator is slow flashing 

• 

Buzzer is slow beeping  

• 

Activate a call point that in the zone in test mode and then 

check the following on the repeater panel: 

• 

Self-test On indicator is slow flashing 

• 

General Fire indicator is on

• 

Correct zone fire indicator is on 

• 

Buzzer is continuous

• 

Take the Zone out of Test Mode at the Fire Panel and reset 

the system . All indications on the repeater should mirror 

those on the Fire Panel . 

Battery Fault Detection Check

Disconnect the battery of the repeater panel .
After about 20 seconds check the Repeater Power Fault indicator 

is on . 
Re-connect the battery of the repeater panel .
After about 4 seconds check the Repeater Power Fault indicator is 

off . 

www.acornfiresecurity.com

www.acornfiresecurity.com

Содержание EFBWCV-REPEATER


















Отзывы: