Eaton DS-206S series Скачать руководство пользователя

Страница: 6 / 96

Instruction Booklet

IB 33-790-1J

Effective November 2010

Instructions for Low Voltage Power

Circuit Breakers Types DS and DSL

EaToN CorPoraTIoN www.eaton.com

List of Illustrations

Figure

Title

Page

The Type DS Low Voltage Power Circuit Breaker Is Shipped Inside Its Own Compartment

Rails Are Stowed Away in the Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Levering Device Crank Handle Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Use of Breaker Lifting Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

View Showing Controls on the Panel (Pre 1988)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Left Side of Breaker with Levering Device Arm in REMOVE Position . . . . . . . . . . . . . . . . . .

DS 416 Breaker with Front Panel Removed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Right Side Showing Levering Device Arm in TEST Position . . . . . . . . . . . . . . . . . . . . . . . . .

Rear View Showing Levering Device Arm in CONNECT Position . . . . . . . . . . . . . . . . . . . . .

Method Used to Press Trip Plate and Lower Shutter with One Hand,

Preparatory to Inserting Crank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front View of Mechanism (Manual Spring Charge Except for DS-632/840) . . . . . . . . . . . . .

Front View of Mechanism (Power-Operated Spring Charge) . . . . . . . . . . . . . . . . . . . . . . . . .

Rear of Power-operated Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear View of Mechanism (Left Close Spring Removed) . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Arrangement of the Principal Parts of a Power Operated Mechanism

The Close Spring is Shown in the Charged Position . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Front View Showing Major Parts of the Crank Shaft Assembly

Some Parts are Omitted for Clarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power-operated Spring-charge Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Crank Shaft Assembly of Power-operated Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Emergency Spring-charge on Power-operated Mechanism . . . . . . . . . . . . . . . . . . . . . . . . .

Standard Schematic and Connection Diagrams for Power-Operated Breakers . . . . . . . . . . .

Principal Parts in a Manually Charged Spring Operated Mechanism . . . . . . . . . . . . . . . . . .

Spring-charging Mechanism on Manual Operated Breakers . . . . . . . . . . . . . . . . . . . . . . . . .

These Sketches Show the Four Basic Positions of Breaker and Linkage

with Enlarged View of Tr ip Shaft and Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Shunt Trip Details Showing Tr ip Shaft Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

265

Actuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DS-632 Breaker with Front Panel Removed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26a

Bottom View of Breaker Unit Showing Interference Interlock,

Motor Cut-off Switch and Other Details not Visible from Above . . . . . . . . . . . . . . . . . . .

Front View Showing Close Bar Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear View Showing the Seismic Positioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Drawout Unit Position Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Relation of Shutter, Tr ip Plate, and Tr ip Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Relation of Shutter, Interlock Cam, and Levering Device Arms . . . . . . . . . . . . . . . . . . . . . . .

Close-Release Interlock to Discharge Springs on Levering Out of Compartment and

Conn. Position No Manual Close Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Close Interlock to Prevent Efforts to Close a Breaker that Is Already Closed . . . . . . . . . . . .

Padlock Device - Locked Tr ip Free and Shutter Raised . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Three-Pole Assembly of DS-206 Pole Units on Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Three-Pole Assembly of DS-416 and DS-420 Pole Units on Frame . . . . . . . . . . . . . . . . . . .

Three-Pole Assembly of DS-632 Pole Units on Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Three Pole Assembly of DS-840 Pole Units on Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Type DS-206 Pole Unit Assembly - Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Type DS-206 Pole Unit Assembly - Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

View Showing Controls on the Panel (Post 1988)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Содержание DS-206S series

































































































Результаты поиска

Содержание DS-206S series

Отзывы:

Похожие инструкции для DS-206S series

Бренды по названию

Популярные бренды

Eaton DS-206S series, Инструкция по эксплуатации

Результаты поиска

Содержание DS-206S series

Отзывы:

Похожие инструкции для DS-206S series

Бренды по названию

Популярные бренды