Eaton Cutler-Hammer Ampgard SC9000 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

background image

I.B. 48003

Page 12

Effective 11/97

1

Remove the two positioning bolts
(A). Free the clevis attached to
the mechanical interlock arm.
See Figure 8 on Page 6. Save
all hardware.

2

Remove three power circuit fuses
(B) using the fuse puller (K)
supplied. See operating
instructions inside medium-
voltage door (C).

3

Separate the contactor side of the
control wires from the terminal
block (D).

4

Disconnect the auxiliary contact
terminal blocks (H) on the
isolating switch.

5

Remove contactor (E) with a
sharp pull forward.

6

Part way out the contactor will
reach a balanced position. Lower
the contactor to the floor and slide
it out of the way. The contactor
weighs approximately 160 lbs. (73
kilograms). If a contactor is
installed in an upper compartment,
an industrial lift with a platform is
necessary.

«
...
10
11
12
13
14
...
»

Содержание Cutler-Hammer Ampgard SC9000

























Отзывы:

Нет отзывов

Похожие инструкции для Cutler-Hammer Ampgard SC9000

Бренд: Parker Страницы: 39

Бренд: ebm-papst Страницы: 10

Z62-M450.01 S21

Бренд: Jäger Страницы: 36

Бренд: Siruba Страницы: 30

Бренд: Parker Страницы: 46

OmniCure 1500 Series

Бренд: Lumen Dynamics Group Страницы: 2

Бренд: R.V.R. Elettronica Страницы: 32

Бренд: ALEGRE Страницы: 19

Бренд: Lennox Страницы: 25

Бренд: Magpowr Страницы: 10

Бренд: GEITH Страницы: 58

Бренд: Commell Страницы: 33

GRASPRESSO GP50-15

Бренд: GRAVEDA Страницы: 32

Бренд: REMS Страницы: 112

Бренд: ABB Страницы: 142

GBAC ROTO BONDER

Бренд: Duro Dyne Страницы: 12

FO Field Patch set

Бренд: R&M Страницы: 2

Бренд: Workhorse Products Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды