Eaton 380 VCP-W 21 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 62

background image

I.B. 3A74792H08

P a g e iii

Effective

09/2014

WARNING

WARNING

IMPROPERLY INSTALLING OR MAINTAINING
THESE PRODUCTS CAN RESULT IN DEATH,
SERIOUS PERSONAL INJURY, OR PROPERTY
DAMAGE.

READ AND UNDERSTAND THESE INSTRUCTIONS
BEFORE ATTEMPTING ANY UNPACKING,
ASSEMBLY, OPERATION OR MAINTENANCE OF
THE CIRCUIT BREAKERS.

INSTALLATION OR MAINTENANCE SHOULD BE
ATTEMPTED ONLY BY QUALIFIED PERSONNEL.
THIS INSTRUCTION BOOK SHOULD NOT BE
CONSIDERED ALL INCLUSIVE REGARDING
INSTALLATION OR MAINTENANCE
PROCEDURES. IF FURTHER INFORMATION IS
REQUIRED, YOU SHOULD CONTACT EATON.

THE CIRCUIT BREAKER ELEMENTS DESCRIBED
IN THIS BOOK ARE DESIGNED AND TESTED TO
OPERATE WITHIN THEIR NAMEPLATE RATINGS.
OPERATION OUTSIDE OF THESE RATINGS MAY
CAUSE THE EQUIPMENT TO FAIL, RESULTING IN
DEATH, BODILY INJURY AND PROPERTY
DAMAGE.

ALL SAFETY CODES, SAFETY STANDARDS
AND/OR REGULATIONS AS THEY MAY BE
APPLIED TO THIS TYPE OF EQUIPMENT MUST BE
STRICTLY ADHERED TO.

THE FIXED CIRCUIT BREAKER ELEMENTS ARE
DESIGNED TO BE INSTALLED PURSUANT TO
ALL APPLICABLE ANSI STANDARDS. SERIOUS
INJURY, INCLUDING DEATH, CAN RESULT FROM
FAILURE TO FOLLOW PROCEDURES OUTLINED
IN THIS MANUAL, OR COMPLY WITH THE
REQUIREMENTS OF APPLICABLE STANDARDS.
THE CUSTOMER IS RESPONSIBLE FOR
PROVIDING ALL REQUIRED PHASE TO PHASE
INSULATION, PHASE TO GROUND INSULATION
AND ALL BREAKER INTERLOCKS. THESE
CIRCUIT BREAKER ELEMENTS ARE SOLD
PURSUANT TO A NON-STANDARD PURCHASING
AGREEMENT WHICH LIMITS THE LIABILITY OF
THE MANUFACTURER.

Eaton Corporation

Moon Township, PA. 15108

A l l possible contingencies which may arise during installation, operation or maintenance, and all details
and variations of this equipment do not purport to be covered by these instructions. If further information
is desired by purchaser regarding his particular installation, operation or maintenance of particular
equipment, contact a Eaton representative.

«
1
2
3
4
5
...
»

Содержание 380 VCP-W 21































































Отзывы:

Нет отзывов

Похожие инструкции для 380 VCP-W 21

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 60

Бренд: Eaton Страницы: 106

Cutler-Hammer Digitrip 1150

Бренд: Eaton Страницы: 84

Бренд: Eaton Страницы: 8

Бренд: Eaton Страницы: 68

Ulusoy URING12-24-LLC-SF6

Бренд: Eaton Страницы: 26

T8-3-8212/E/HI12

Бренд: Eaton Страницы: 2

MINIA MMR-X3-001-A230

Бренд: OEZ Страницы: 10

Бренд: Eaton Страницы: 2

SE-BL-MTV8 Series

Бренд: OEZ Страницы: 8

Бренд: Siemens Страницы: 10

Бренд: Siemens Страницы: 10

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 96

Бренд: Siemens Страницы: 6

Бренд: ABB Страницы: 16

SACE Emax Series

Бренд: ABB Страницы: 161

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды