Eaton 380 VCP-W 21 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 62

background image

Page 10

I.B. 3A74792H08

Effective

09/2014

Figure 3-1 Circuit Breaker Shown Mounted with Ramp
Still in Shipping Position (VCP-W Only)

Step 1:

VCP-WR breakers must be lifted from the

shipping pallet. Refer to paragraph 3-5 for
the optional lifting yoke used with an
overhead lifting device after all shipping
hardware used to hold the breaker to the
skid is removed.

Step 2:

For VCP-W breakers, remove the vertically

mounted ramp from the shipping skid and
place it on the floor next to the skid. It
should be positioned with the highest part
of the ramp next to the side of the skid with
the front of the circuit breaker.

Step 3:

Remove the shipping brackets used to hold

the circuit breaker to the skid. Use the
same shipping brackets and hardware to
attach the ramp to the shipping skid.

Step 4:

Slowly move the circuit breaker forward and

down the ramp. Make certain that the
circuit breaker moves down the ramp
slowly and straight in line with the ramp.
Once the circuit breaker is on the floor, it
can be easily maneuvered via its integral
wheels.
VCP-W breakers can also be lifted using the

Figure 3-2 Circuit Breaker Shown Being Moved

Figure 3-3 Optional Fifth Wheel Shown in
Use (VCP-W Only)

3. 4 STO R AGE

If the circuit breaker is to be placed in storage, maxi-

«
...
14
15
16
17
18
...
»

Содержание 380 VCP-W 21































































Отзывы:

Нет отзывов

Похожие инструкции для 380 VCP-W 21

Бренд: Siemens Страницы: 10

3WN6 3WX3663-6JE.0

Бренд: Siemens Страницы: 12

Бренд: Siemens Страницы: 15

Бренд: Westinghouse Страницы: 38

DE-ION 150-DH-250-A

Бренд: Westinghouse Страницы: 21

Бренд: Eaton Страницы: 3

Бренд: Westinghouse Страницы: 47

Бренд: Eaton Страницы: 72

Бренд: NHP Страницы: 16

Бренд: CHINT Страницы: 6

Бренд: Apator Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды