Eaton 380 VCP-W 21 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 62

background image

Page 18

I.B. 3A74792H08

Effective

09/2014

SECTION 4: INITIAL INSPECTION AND
INSTALLATION

4-1 INTRODUCTION

WARNING

BEFORE PLACING THE CIRCUIT BREAKER IN
SERVICE, CAREFULLY FOLLOW THE
INSTALLATION PROCEDURE GIVEN BELOW. NOT
FOLLOWING THE PROCEDURE CAN FAIL TO
UNCOVER SHIPPING DAMAGE THAT MAY RESULT
IN INCORRECT CIRCUIT BREAKER OPERATION
LEADING TO DEATH, BODILY INJURY, AND
EQUIPMENT DAM-AGE.

Before attempting to put a circuit breaker in service, it
should be carefully examined and operated manually and
electrically. In addition, carefully examine the breaker for
loose or obviously damaged parts. The following
information is a guide for performing recommended
checks and tests.

4-2 MANUAL OPERATION CHECK

Refer to Figures

3-8

and

4-1

and then proceed by placing

the maintenance tool into the manual charge socket
opening. Charge the closing springs with about 38 up
and down strokes of the handle. When charging is
complete the closing crank goes over center with an
audible

CLICK

and the springs Charged/Discharged

indicator shows “Charged.”

NOTICE

If the springs are to be charged on a closed circuit
breaker, no click is heard at the end of charging
operation. Discontinue charging and remove the
maintenance tool as soon as “Charged” flag is fully
visible. Continued attempts to charge further may
result in damage to the mechanism.

Remove the maintenance tool. Close and trip the circuit
breaker. Repeat several times.

4-3 VACUUM INTERRUPTER INTEGRITY

Using a dry, lint free cloth or paper towel, clean all the
accessible insulating surfaces of the pole units. Conduct a
vacuum interrupter integrity check as described in
Section 6.

4-4 INSULATION

Check the circuit breaker’s primary and secondary
insulation as described in Section 6.

4-5 CONTACT EROSION AND WIPE

Manually charge the closing springs and close the
circuit breaker. Check contact erosion and wipe as
described in Section 6.

4-6 PRIMARY CIRCUIT RESISTANCE

Check the primary circuit resistance as described in
Section 6. The resistance should not exceed the
values specified. Record the values obtained for
future reference.

4-7 NAMEPLATE

Compare the circuit breaker nameplate information
with switchgear drawings for compatibility.

4-8 ELECTRICAL OPERATION CHECK

After having completed all previous checks and tests,
the circuit breaker is ready to be operated electrically.
It is preferred that this check be made with the circuit

Figure 4-1 Type VCP-W Circuit Breaker Manual
Charging Handle in Use

«
...
22
23
24
25
26
...
»

Содержание 380 VCP-W 21































































Отзывы:

Нет отзывов

Похожие инструкции для 380 VCP-W 21

Бренд: Eaton Страницы: 15

Бренд: Eaton Страницы: 10

Бренд: Fluke Страницы: 5

PRO SERIES THE MAESTRO

Бренд: Power Probe Tek Страницы: 31

Бренд: ABB Страницы: 56

PKZM0 SP-65KA Series

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: IDEAL Страницы: 54

Бренд: GenInterlock Страницы: 2

Бренд: GenInterlock Страницы: 2

Бренд: GenInterlock Страницы: 2

Бренд: GenInterlock Страницы: 2

Бренд: GenInterlock Страницы: 2

Бренд: GenInterlock Страницы: 2

Бренд: GenInterlock Страницы: 2

Бренд: GenInterlock Страницы: 2

Бренд: GenInterlock Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды