4
Figure 7
Connection Panel Low er Right Side
Autolite W iring Diagram
Figure 9
Door handle assem bly
Note - For best insert operation the flexible vent
installation should not have any tight bends. Try to
achieve a smooth sw eep to the vertical rise.
SURROUND INSTALLATION
The surround supplied with the insert is adjustable in
height so as to allow for m any installation perim eters.
1.
After the insert is in position, install left and right surround
sides by attaching them to the two side brackets using the
four 1/4-20 bolts provided. The retainer nuts on the
surround sides m ay be installed at any vertical position to
accom m odate the installation.
2.
Slide the surround top panel between the hopper top and
cover. Push the panel down until the screw holes align
with the side legs. Install the (4) #8 screws provided.
Install power cord into the receptacle on the right side of
the insert. Route cord behind surround leg and out to a
ground plus.
AUTOLITE INSTALLATION INSTRUCTIONS
The AutoLite System is factory installed with the only
installation requirem ents being the optional therm ostat.
Wall Thermostat Installation:
The wall therm ostat is designed to autom atically regulate
the room tem perature from the control panel heat setting to
the “Off” setting based upon room tem perature. Rem em ber
to leave the control panel on the "Medium or High" position
when utilizing the wall therm ostat feature.
The following is a step by step procedure for installing the
optional wall therm ostat. Note connection term inals on left
side of unit at rear (
Figure 7
). Use 18/2 therm ostat wire for
the installation.
a.
Unplug heater from wall outlet and 12VDC power!
b.
Rem ove factory jum p wire and hook up therm ostat
wires to term inals (
Figure 7
).
c.
Locate therm ostat approxim ately 10 to 12 feet from
heater or in area that requires steady tem perature.
d.
Run therm ostat wires from heater to therm ostat along
wall or under carpet etc. and hook wires to
therm ostat term inals. On new construction you can,
of course, run wire in the walls before sheet rock or
paneling is done.
e.
Reconnect AC power.
f.
Make sure all wiring is com pleted before plugging the
EASYFIRE Heater back into the wall outlet.
IM PORTANT
- Any electrical work perform ed on the
EASYFIRE Heater should be done by qualified personnel.
Remote Control Thermostat Installation:
The rem ote therm ostat is designed to autom atically
regulate the room tem perature from the control panel heat
setting to the “Off” setting based upon room tem perature
and placem ent of the rem ote therm ostat. Rem em ber to
leave the control panel on the "Medium or High" position
when utilizing the wall therm ostat feature.
The following is a step by step procedure for installing the
optional rem ote therm ostat. Note connection term inals on
rear of unit (
Figure 7
).
a.
Unplug heater from wall outlet and 12VDC power!
b.
Mount m illivolt style rem ote receiver box to rear of
stove using double-sided tape.
b.
Rem ove factory jum p wire and hook up therm ostat
wires to term inals (
Figure 7
).
d.
Reconnect AC power and follow instructions with
rem ote therm ostat regarding set up.
IM PORTANT
- Any electrical work perform ed on the
EASYFIRE Heater should be done by qualified personnel.
DOOR HANDLE ASSEMBLY
The door handle and latch m ust be assem bled and
adjusted prior to the operation of the stove.
1. Position handle assem bly through door and secure with
collar by sliding over shaft and tightening with allen
wrench provided.
2. Position latch on end of shaft with flat facing allen screw.
Depending on gasket, shaft will protrude approx. 1/4"
through back of latch collar. Snug allen screw.
3. To adjust door, close and turn handle so latch contacts
striker. Door gasket m ust contact firm ly against front face
of unit. This can be checked by closing against a piece of
paper. Firm ly tug on paper, if it m oves with solid
resistance the door is properly adjusted.
