![background image](http://html1.mh-extra.com/html/earlex/spray-station-hv5500/spray-station-hv5500_main-manual-and-safety-instructions_3410297003.webp)
3
●
WARNING: The substances used with this
spray gun (paint, thinners, etc) may contain
hazardous, harmful, explosive or corrosive
materials. ALWAYS COMPLY WITH THE
SAFETY INSTRUCTIONS ISSUED WITH
THIS PRODUCT AND THE MATERIAL
BEING USED.
Only use the unit as detailed in these
instructions.
●
NEVER under any circumstances aim the
nozzle at another person or animal. In the
event of injury occurring seek expert medical
advice immediately.
●
The spray gun must only be used with paints
and solvents that have a suitable flash point for
spraying. If in doubt consult paint or solvent
manufacturer’s data.
●
Always ensure there is adequate ventilation
when spraying.
●
NEVER spray near a naked flame, including
appliance pilot flame.
●
NEVER use this spray gun outside when
raining.
●
NEVER smoke whilst spraying.
●
NEVER allow children to operate or play with
the spray gun.
●
Always read the paint manufacturer’s thinning
instructions before use.
●
Always disconnect unit from mains supply
when refilling the paint container.
●
If the supply cord is damaged, it must be
replaced by Earlex Ltd or our appointed agents
to avoid a hazard.
●
Before cleaning, always disconnect unit from
the mains supply.
●
Always wear the correct protective face mask
when spraying. We recommend the use of
gloves, goggles and overalls.
●
After every use ensure that you clean your
spray gun thoroughly and grease the fluid
needle packing.
●
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given supervision
or instruction concerning use of the appliance
in a safe way and understand the hazards
involved. Children shall not play with the
appliance. Cleaning and user maintenance
shall not be made by children without
supervision.
●
Use only genuine Earlex replacement parts.
●
Earlex recommend the use of appropriate ear
protection when using this product.
●
Sound pressure level: 85 dB (A)
This is a highly versatile spray kit that can be used with several different spray mediums including varnishes, wood preservatives, enamels, oil and
water-based paints and automotive paints. However some materials cannot be sprayed so please check the recommendation of the manufacturer
before buying the paint. If a material refers to brush application only then it usually cannot be sprayed.
THIS UNIT CANNOT BE USED FOR TEXTURED PAINTS. USE OF THESE MATERIALS WILL CAUSE PREMATURE WEAR, WHICH WILL VOID
YOUR GUARANTEE. TO OBTAIN THE BEST RESULTS FROM YOUR SPRAY KIT PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE
USE.
Preparation of the surface and thinning of the paint are the two most important areas to be concerned with to obtain the best results from your spray
kit. Ensure all surfaces are free from dust, dirt, rust and grease. If necessary rub down with sandpaper, or similar. Masking of areas is important to
ensure you do not spray those areas you wish to remain untouched.
Fill the paint container with the material to be sprayed. Take care not to overfill. Stir well using Paint Stirrer (31) supplied.
Take the spray gun unit and with the Clamp Lever (22) turned fully anticlockwise, locate the spray gun unit into the Paint Container (17). Rotate the
container until the 2 pins locate into the recesses in the Yoke (23). Now turn the clamp lever clockwise to secure the paint container to the lid. Do not
over-tighten.
Place the motor unit onto a clean and level floor space, free from any loose debris, liquids or dust sheets that could block the motor inlet. Uncoil the
Air Hose (28) and attach it to the back of the spray gun and the other end to the Spray Station. Uncoil the power cord from the base of the unit and
plug in.
ALWAYS KEEP THE MOTOR UNIT AS FAR AWAY FROM THE SPRAYING AREA AS POSSIBLE TO PREVENT PAINT CONTAMINATING THE
MOTOR. MASK ANY AREA YOU DO NOT WISH TO SPRAY.
Once you have set up and are ready to spray, switch on the unit. No paint will be sprayed from the gun until the trigger on the spray gun is pulled.
Before starting any work on spraying actual objects we suggest you spend time practicing on cardboard or newspaper until you have got used to how
the gun works.
The gun has 3 different spray patterns – Horizontal, Vertical and Round (Fig.2).
The Horizontal and Vertical sprays are recommended for large surfaces. The round spray is used for
small objects or for areas - such as corners – that are difficult to reach.
To change the spray pattern simply rotate the Air Cap (2) until it clicks into the desired settings as shown
in (Fig.2).
The overall size of the selected spray pattern can be varied by turning the Air Cap Ring (1). When viewed
from the front, rotate it clockwise to increase the pattern size or anticlockwise to reduce the pattern size.
Fig.2
Vertical Jet
Round Jet
Horizontal Jet
SAFETY OPERATING INSTRUCTIONS
WARNING! FIRE AND EXPLOSION HAZARD
SELECTING PAINT
SURFACE AND JOB PREPARATION
OPERATION
SPRAY PATTERNS
Содержание Spray Station HV5500
