EAE RCU2018 Скачать руководство пользователя страница 14

Страница: 14 / 81

Product Manual RCUXXYY

EAE KNX Room Control Unit

RCUXXYY PM R1.0

EAE Technology

www.eaetechnology.com

Page 13 / 80

Communication Object Table

The device has 254 communication objects. Overview of all communication objects of the device can
be seen on the following table. Object names will be changed according to channel function as
follows.

Fan coil:

Fan A/B1, Fan C/D1, Fan E/F1, Fan G/H1, Fan I/J1 etc.

Valve control:

Valve A/B, Valve C/D, Valve E/F, Valve G/H, Valve I/J.

Shutter/Blind DC:

Output A/B, Output C/D, Output E/F, Output G/H, Output I/J.

Shutter/Blind AC:

Output A, Output B, Output C, Output D, Output E.

Switch:

Output A1, Output A2, Output B1, Output B2, Output C1, Output C2 etc.

Name

Function

DTP Type

Length

Flags

General

In operation

1.002

1 bit

CWT

General

Scene 8-bit

18.001

1 byte

Blind

Wind alarm

1.005

1 bit

CWTU

Blind

Rain alarm

1.005

1 bit

CWTU

Blind

Frost alarm

1.005

1 bit

CWTU

Input a

Disable

1.003

1 bit

Input a

Switch

1.001

1 bit

CWT

Switch

–

short

1.001

1 bit

CWT

Shutter Up/Down

1.008

1 bit

Value (0,1)

1.001

1 bit

CWT

Value (forced)

2.001

2 bit

CWT

Value [0...255]

5.001

8 bit

CWT

Value [0...65535]

8.001

16 bit

CWT

Value [-32768...32767]

7.001

16 bit

CWT

Value [0...4294967295]

12.001

32 bit

CWT

Input a

Switch

–

long

1.001

1 bit

CWT

Dimming brighter / darker

3.007

4 bit

Shutter stop / lamella

1.007

1 bit

Value (0,1) - long

1.001

1 bit

Value (forced) - long

2.001

1 bit

Value [0...255] - long

5.001

8 bit

Value [0...65535] - long

8.001

16 bit

Value [-32768...32767]

7.001

16 bit

Value [0...4294967295]

12.001

32 bit

Input a

Shutter upper limit position

1.002

1 bit

Value (temperature)

14.068

32 bit

Input a

Shutter lower limit position

1.002

1 bit

Value (temperature) - long

14.068

32 bit

…

Input b … s

Same as

“

Input a

”

Output A1

Switch

1.001

1 bit

Output A
Output A/B

Move blind/shutters up-down

1.008

1 bit

Fan A/B1

Fan speed switch

5.010

1 byte

Control input

Control value HEATING

5.001

1 byte

Содержание RCU2018


















































































Результаты поиска

Содержание RCU2018

Отзывы:

Похожие инструкции для RCU2018

Бренды по названию

Популярные бренды

EAE RCU2018, Руководство по эксплуатации продукта

Результаты поиска

Содержание RCU2018

Отзывы:

Похожие инструкции для RCU2018

Бренды по названию

Популярные бренды