manualshive.com logo in svg

E.T. Systems DC BLUE ADVANCED, Инструкции по установке, Страница: 25 / 32

Поделиться
Скачать
E.T. Systems DC BLUE ADVANCED Скачать руководство пользователя страница 25

ET DC BLUE ADVANCED INSTALLER 2012.025.12.05.2014 

 

25 

www.et.co.za 

 

 

 

ADVANCED OPERATING FEATURES 

 

Advanced triggers using the remote (BT) button trigger  

 

(PARTY MODE) 

 

Example 3. Using the remote (BT)  button trigger to disable any closing triggers  

 

 

Action 

Response 

TO ACTIVATE 

 

 

Door in the closed 

position. 

Courtesy light off. 

 

Press and release either 

the remote button 

trigger or the hardwired 

trigger. 

 

Door begins opening 

and courtesy  light 

switches on.  

 

Stop door while opening 

or simply wait until it 

reaches the open 

position. 

 

Door stops and waits at 

the required open 

position. Courtesy light 

remains on for a further 3 

minutes. 

 

Press and hold the 

remote button trigger, 

+/- 10 seconds, until 

buzzer beeps. 

 

Buzzer beeps rapidly to 

indicate party mode is 

active. 

 

 

TO CONFIRM 

Any  attempt to operate 

the door normally. 

 

Buzzer repeats rapid 

beeps to indicate the 

party mode is still active. 

The door will not move. 

 

 

TO DE-ACTIVATE 

Press and hold the 

remote button t/- 

10 seconds,  until buzzer 

beeps. 

 

Buzzer beeps once and 

door starts closing. 

Courtesy light switches 

on for three minutes. 

 

Rapid 

Rapid 

Содержание DC BLUE ADVANCED

































Отзывы:

Нет отзывов