E-FLITE Deuces Wild ARF Скачать руководство пользователя

Страница: 57 / 68

E-flite Deuces Wild Assembly Manual



3. With the outer wing panel tight against the wing

center section, use a 3/32-inch ball driver to install the

4-40 x 1-inch socket head bolt that secures the outer

panel to the center section. Complete for the opposite

wing panel.



4. Position the wing on the fuselage. Use two 1/4-20 x

2-inch nylon bolts and a flat screwdriver to secure the

wing to the fuselage. Ensure you connect the air lines as

well as the servo wires from the wing into the respective

ports on the receiver before fully installing the wing.

Canopy and Gear Door Installation

Required Parts

Fuselage assembly

Canopy

Tie wrap (4)

Main gear door (right and left)

Required Tools and Adhesives

Low-tack tape

Canopy glue

Side cutters

Drill

Drill bit: 5/64-inch (2mm)

Silicone adhesive

Note

: You may wish to install the optional cockpit kit at

this time. Instructions have been provided with that kit on

how to install it into your Deuces Wild.



1. Use canopy glue to attach the canopy to the fuselage.

Use low-tack tape to hold the canopy in position until the

glue has fully cured.

Содержание Deuces Wild ARF





































































Результаты поиска

Содержание Deuces Wild ARF

Отзывы:

Похожие инструкции для Deuces Wild ARF

Бренды по названию

Популярные бренды

E-FLITE Deuces Wild ARF, Инструкция по сборке

Результаты поиска

Содержание Deuces Wild ARF

Отзывы:

Похожие инструкции для Deuces Wild ARF

Бренды по названию

Популярные бренды