background image

EN

23

Compliance Information for the European Union

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it 
is the user’s responsibility to dispose of their waste equipment by 
handing it over to a designated collections point for the recycling of 
waste electrical and electronic equipment. The separate collection 
and recycling of your waste equipment at the time of disposal will 

help to conserve natural resources and ensure that it is recycled in a manner that 
protects human health and the environment. For more information about where 
you can drop off your waste equipment for recycling, please contact your local city 
offi ce, your household waste disposal service or where you purchased the product.

EU Compliance Statement:
EFL Carbon-Z Carbon Cub SS BNF Basic (EFL12450)

 Horizon Hobby, LLC hereby declares that this product is in compliance 
with the essential requirements and other relevant provisions of the 
RED and EMC Directives. 

A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.

EFL Carbon-Z Carbon Cub SS PNP (EFL12475)

Horizon Hobby, LLC hereby declares that this product is in compliance with the 
essential requirements and other relevant provisions of the EMC Directive. 
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.

IC Information

FCC Information

IC ID:

 

6157A-AMRX15

CAN ICES-3 (B)/NMB-3(B) 

This device complies with Industry Canada licence-exempt RSS standard(s). 
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any 
interference, including interference that may cause undesired operation of the device.

FCC ID: BRWDASRX15

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this 
device must accept any interference received,including interference that may cause undesired operation.

CAUTION:

 Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a 

radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

Supplier’s Declaration of Conformity

EFL Carbon-Z Carbon Cub SS BNF Basic and PNP  (EFL12450, EFL12475)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) 

this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

 changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, 
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC 
2904 Research Rd.,
Champaign, IL 61822
Email: [email protected]
Web: HorizonHobby.com

Содержание Carbon-Z Cub SS

























Отзывы: