background image

EN

Carbon-Z Cub SS

10

AILE

FLAP

AILE

FLAP

D

A

B

C

G

Model Assembly 

(Continued)

Wing Installation (Continued)

1.  Slide the wing tube (

A

) into the fuselage.

2.  Install the left and right wing (

B

 and 

C

) onto the wing tube.

3.  Connect the servo connectors (

D

) to the respective connectors on the fuselage 

(connectors are marked AIL or FLAP) and slide the wing into the slot of the 
fuselage.

NOTICE:

 Always put excess servo connector wire into the pocket of the wing to 

prevent pinching of wires or other damage.

4.  Secure the wings on the fuselage using 4 thumb screws (

E

) in the holes on the 

top of the wings.

5.  Install the 2 antenna (

F

) on top of the two rear thumb screws by pressing them 

onto the thumb screw. 

6.  Connect the left and right wing struts to the fuselage mounts (

G

) using 4 pins 

(

H

) and 4 R-clips (

I

).

Removal

We recommend removing the wings from the fuselage for storage or transport of 
the aircraft. 

TIP:

 Remove the jury strut pins and clips from the struts to pivot the brackets 

and struts down to the wings. Wing struts do not need to be disassembled to be 
removed. 

NOTICE:

 Always secure loose parts after removal. DO NOT FLY if parts are 

missing or damage may result.

(

E

) 3 x 25mm

Thumb Screw

Bag K

Bag K

(

F

) Antenna Cap

Bag L

(

H

)

Bag L

(

I

)

Содержание Carbon-Z Cub SS

























Отзывы: