Dynamic Engineering PMC-XM-DIFF Скачать руководство пользователя | Manualshive

Страница: 16 / 46

background image

Embedded Solutions

Page 16 of 46

occur. This bit is useful for software development and debugging.
Transmit Enable: When this bit is ‘1’, the transfer state machine is enabled to move data
from the referenced channel’s transmit FIFO to the corresponding Virtex transmit FIFO.
When this bit is ‘0’, the transmit transfer state machine is disabled.

Receive Enable: When this bit is ‘1’, the transfer state machine is enabled to move data
from the referenced channel’s Virtex receive FIFO to the corresponding local receive
FIFO. When this bit is ‘0’, the receive transfer state machine is disabled.

Virtex Interrupt Enable: When this bit is ‘1’, the corresponding Virtex interrupt (VINT0 for
channel 0 or VINT1 for channel 1) is enabled to cause a system interrupt when active.
When this bit is ‘0’, the Virtex interrupt can not cause a system interrupt.

DMA Write Arbitration Priority Enable: When this bit is ‘1’, the write DMA for the
referenced channel will receive priority if the TX FIFO has become almost empty as
defined by the value stored in the TX_AMT_LVL register. When this bit is ‘0’, the DMA
arbitration will follow round-robin arbitration priority.

DMA Read Arbitration Priority Enable: When this bit is ‘1’, the read DMA for the
referenced channel will receive priority if the RX FIFO has become almost full as
defined by the value stored in the RX_AFL_LVL register. When this bit is ‘0’, the DMA
arbitration will follow round-robin arbitration priority.

«
...
14
15
16
17
18
...
»

Содержание PMC-XM-DIFF















































Отзывы:

Нет отзывов

Похожие инструкции для PMC-XM-DIFF

Бренд: Makerfire Страницы: 10

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: BACtrack Страницы: 13

Бренд: TA Instruments Страницы: 35

Бренд: TC Electronic Страницы: 2

Бренд: Bahco Страницы: 131

Бренд: Bahco Страницы: 126

Бренд: Idex Страницы: 141

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Бренд: Ransomes Страницы: 282

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды