Dynamic Engineering PMC-XM-DIFF Скачать руководство пользователя | Manualshive

Страница: 11 / 46

background image

Embedded Solutions

Page 11 of 46

Register Definitions

PMC_XM_BASE

[0x0000] Base Control Register (read/write)

Base Control Register

Data Bit

Description

31-17

Spare

16

Load Virtex

15-10

Spare

9

Virtex Init

8

Virtex Reset

7

Virtex Flash Enable

6

Slave Serial Mode Enable

5

Virtex Program Init

4

Virtex Program Select

3

Flash Select

2

Flash Control

1

Force Interrupt

0

Master Interrupt Enable

FIGURE 3

PMC-XM SPARTAN3 BASE CONTROL REGISTER

All bits are active high and default to ‘0’ on reset or power-up.

Master Interrupt Enable: This bit enables the interrupts for the base portion of the XM
design. When this bit is a ‘1’, the interrupt is enabled; and when this bit is a ‘0’ the
interrupt is disabled. Currently the only interrupt source for this portion of the design is
the Force Interrupt bit.

Force Interrupt: When this bit is ‘1’ and the Master Interrupt Enable is ‘1’, an interrupt
will be generated. This bit is useful for software development and debugging.

Flash Control: When this bit is ‘1’, the Flash Select bit controls which Flash Prom is
connected to the JTAG port. When this bit is ‘0’, I/O bit 63 controls the selection. When
I/O bit 63 is grounded, the Virtex Flash is selected; when I/O bit 63 is open, the signal is
pulled high and the Spartan3 Flash is selected.

Flash Select: When Flash Control is set to ‘1’ this bit controls which Flash Prom is
connected to the JTAG port. When Flash Select is ‘0’, the Virtex Flash is selected;
when Flash Select is ‘1’, the Spartan3 Flash is selected. When Flash Control is ‘0’, this
bit has no effect.

«
...
9
10
11
12
13
...
»

Содержание PMC-XM-DIFF















































Отзывы:

Нет отзывов

Похожие инструкции для PMC-XM-DIFF

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: 3M Страницы: 48

Бренд: 3M Страницы: 19

Speedglas G5-01

Бренд: 3M Страницы: 62

Quickfit Nexus Exit

Бренд: Thomas & Betts Страницы: 2

Бренд: Tate Страницы: 7

Бренд: Tate Страницы: 5

BioHarmonex BH4

Бренд: Calivita Страницы: 38

Бренд: CAIRE Страницы: 91

Heart Guardian AED

Бренд: Radian Страницы: 36

Бренд: GE Страницы: 2

Бренд: Kelvin Страницы: 30

Бренд: Vibration Research Corporation Страницы: 333

MIDORI ULB-50sc

Бренд: Ushio Страницы: 24

Бренд: AVID LABS Страницы: 20

Бренд: Briteq Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды