background image

- 31  - 

Technical Support 

 
If you have questions about this product, or if you experience difficulties during the installation, 
contact DX Engineering at (330) 572-3200.  You can also e-mail us at:       
 

[email protected]

 

 

For best service, please take a few minutes to review this manual before you call. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Warranty 

 
All products manufactured by DX Engineering are warranted to be free from defects in material and 
workmanship for a period of one (1) year from date of shipment. DX Engineering’s sole obligation under 
these warranties shall be to issue credit, repair or replace any item or part thereof which is proved to be other 
than as warranted; no allowance shall be made for any labor charges of Buyer for replacement of parts, 
adjustment or repairs, or any other work, unless such charges are authorized in advance by DX Engineering.  
If DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering shall, 
upon prompt notice thereof, issue shipping instructions for return to DX Engineering (transportation-charges 
prepaid by Buyer). Every such claim for breach of these warranties shall be deemed to be waived by Buyer 
unless made in writing. The above warranties shall not extend to any products or parts thereof which have 
been subjected to any misuse or neglect, damaged by accident, rendered defective by reason of improper 
installation, damaged from severe weather including floods, or abnormal environmental conditions such as 
prolonged exposure to corrosives or power surges, or by the performance of repairs or alterations outside of 
our plant, and shall not apply to any goods or parts thereof furnished by Buyer or acquired from others at 
Buyer’s specifications. In addition, DX Engineering’s warranties do not extend to other equipment and parts 
manufactured by others except to the extent of the original manufacturer’s warranty to DX Engineering.  The 
obligations under the foregoing warranties are limited to the precise terms thereof. These warranties provide 
exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential 
damages. SELLER NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, 
WHETHER EXPRESS, STATUTORY, OR IMPLIED, INCLUDING WARRANTIES OF 
MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO ASSUME FOR DX 
ENGINEERING ANY OBLIGATION OR LIABILITY NOT STRICTLY IN ACCORDANCE WITH THE 
FOREGOING. 
 
©DX Engineering 2012 
 
DX Engineering®, DXE®, DX Engineering, Inc.®, Hot Rodz®, Maxi-Core®, DX Engineering 
THUNDERBOLT™, DX Engineering Yagi Mechanical®, EZ-BUILD®, TELREX® and Gorilla Grip® 
Stainless Steel Boom Clamps, are trademarks of PDS Electronics, Inc. No license to use or reproduce any of 
these trademarks or other trademarks is given or implied. All other brands and product names are the 
trademarks of their respective owners.   
 
Specifications subject to change without notice. 
 
 

Содержание THUNDERBOLT DXE-MBVA-1UP

































Отзывы: