DUROMAX XP13000HXT страница 30 Скачать руководство пользователя

Страница: 30 / 82

Step 1 - Check the oil

Check the oil

The generator is equipped with an automatic shutoff to

protect it from damage due to low oil. Nonetheless, you

should check the oil level of the engine before each use to

ensure that the engine crankcase has a sufficient amount.

To check the oil level:

Make sure the generator is on a level surface.

Unscrew the oil filler/dipstick cap.

With a dry cloth, wipe the oil off of the stick on the

inside of the cap.

Insert the dipstick as if you were replacing the

cap and then remove it again. There should now be

oil on the stick. If there is no oil on the stick, or oil

only at the very end of the stick, you should add

oil until the engine crankcase is filled (see “Adding

Oil” portion of the “Maintenance” section).

Be sure to replace the cap when finished checking

oil.

BEFORE YOU START YOUR GENERATOR

Model Number

XP13000HXT

Engine Oil Capacity

40.5 fl. oz (1.2L)

Содержание XP13000HXT



















































































Результаты поиска

Содержание XP13000HXT

Отзывы:

Похожие инструкции для XP13000HXT

Бренды по названию

Популярные бренды

DUROMAX XP13000HXT, Руководство пользователя

Результаты поиска

Содержание XP13000HXT

Отзывы:

Похожие инструкции для XP13000HXT

Бренды по названию

Популярные бренды