DUROMAX XP13000HXT страница 52 Скачать руководство пользователя

Страница: 52 / 82

Idle Control

The idle control feature lowers the RPM of the generator
when there is no load to save gas and decrease engine
noise.

When a load is applied, the engine will resume normal
speed to provide usable power.

Turn on the idle control when using intermittent loads like
power tools and air compressors.

The idle control feature is designed for gasoline only use.

Idle Control Usage

WARNING

: Power is unusable when idle control is engaged.

●

DO NOT use the idle control function when using the generator for backup house
power.

●

Idle control function will cause massive fluctuations in voltage and hertz.

●

Low amperage loads may not trigger the idle up function.

USING THE GENERATOR (CONTINUED)

Содержание XP13000HXT



















































































Результаты поиска

Содержание XP13000HXT

Отзывы:

Похожие инструкции для XP13000HXT

Бренды по названию

Популярные бренды

DUROMAX XP13000HXT, Руководство пользователя

Результаты поиска

Содержание XP13000HXT

Отзывы:

Похожие инструкции для XP13000HXT

Бренды по названию

Популярные бренды