DUROMAX XP13000HXT страница 16 Скачать руководство пользователя

Страница: 16 / 82

GENERATOR COMPONENTS

4. Fuel Tank

2. Air Cleaner

6. Handles

7. Battery

8. Oil Fill and Dipstick

1. Recoil Start

Recoil Start

– Easy Pull Recoil Start to start the engine without the electric start.

Air Cleaner

- A removable, cleanable, oiled element that cleans the air going into the engine.

Fuel Valve

- On/Off valve that allows gasoline to the fuel switch.

Fuel Tank

- All-metal 8.3 gallon gasoline fuel tank.

Power Panel

- Contains the start switch, plugs, meters, and circuit breakers.

Handles

- Long handles allow maneuvering

acr

oss any surface

Battery

- 12V DC Battery that powers the Electric Start System.

Oil Fill and Dipstick

- Use to add or check the oil.

Gas Type -

Fuel selection switch to choose Gas/Propane, or Natural Gas.

10.

LPG/NG Inlet

- Provides a regulated LPG/NG Fuel supply to the engine.

11.

Fuel Type -

Fuel selection switch to choose Gas, Propane/NG, or Storage.

12.

Engine Switch

– Push Button Start switch. Press for 1 second to start the generator. Hold for

3 seconds to stop the generator.

13.

Charging Light

- Lights up when the generator is charging the on-board battery.

5. Power Panel

3. Fuel Valve

14. Low Oil Alert

21. GFCI 20A Receptacles

Содержание XP13000HXT



















































































Результаты поиска

Содержание XP13000HXT

Отзывы:

Похожие инструкции для XP13000HXT

Бренды по названию

Популярные бренды

DUROMAX XP13000HXT, Руководство пользователя

Результаты поиска

Содержание XP13000HXT

Отзывы:

Похожие инструкции для XP13000HXT

Бренды по названию

Популярные бренды