background image

23

EXTERNAL  CABLE  ASSEMBLIES

 6-Track Analog Audio Output Cable for DTS-6D  -  2503-0014-00

  

(same part as logic cbl)

This cable connects the 6 channel DTS-6D output to an analog cinema processor.

 6-Track Digital Audio Output Cable for DTS-6D  -  D713

This cable connects the 6 channel DTS-6D output to a digital cinema processor.

 Automation (logic) Cable for DTS-6D  -  2503-0014-00

  

(same part as analog output cbl)

This cable connects the DTS-6D logic circuitry to the cinema processor.

 SMART  Interface Cables

The following DTS cables connect the 6 channel DTS analog output to 

SMART

 cinema processors.  The 

SMART

processor does not use any DTS external breakout boards.  For the Mod V, use the DTS  D714 cable.  For the Mod
VI, use the  DTS  D706 cable.

 Timecode Cable Assembly - D435

This cable connects the DTS Timecode Reader Head to the DTS-6D Processor.  On single projector (platter)
systems, this cable has a single connector at both ends.  For dual (change-over) projector systems, this cable has a
single connector at one end and two connectors at the other end.  See D477 for assembly diagram.

EXTERNAL  BREAK-OUT  BOARDS

 Logic Break-out  Boards

These boards are used to pulse to the cinema processor to the correct playback format.  The analog default is
automatic or can be hard-wired forced to SR or A-type.

*  D716 is used with the Dolby CP45
*  D565 is used with the Dolby CP55
*  D564 is used with the Dolby CP65
*  D567 and one D711 cable are used with the Dolby CP200, CP100, CP50
*  D715 is used with the Dolby CP500.  D715 contains programming jumpers that must be set correctly.
*  D571 is used with UltraStereo

 Audio Break-out  Boards

These boards are used to connect DTS 6-track outputs to an analog cinema processor/speaker amp.

*  D574 is used with the Dolby CP45 and CP65
*  D572 is used with the Dolby CP55

D572 contains a programming jumper, set for  

MONO SURR 

 or 

 STEREO

  surround

*  Two D712 cables are used with the DTS D567 board (

mentioned above

) for the Dolby CP200, CP100, CP50

D567 RevB or lower, contains three programming jumpers, set all -3- for either 

DRY 

(standard configuration) position  or  

MONO  SURR

(SR-D

TM

 application) position.

*  D575 is used with UltraStereo
*  The CP500 does not use an audio break-out board.
*  D725 (dual input) is used with CP65 and audio dubber

Содержание DTS-6D









































































Отзывы: