![DTS DTS-6D Скачать руководство пользователя страница 10](http://html1.mh-extra.com/html/dts/dts-6d/dts-6d_installation-and-operation-manual_2536096010.webp)
4
3.2
DTS-6D Processor Installation
DTS has configured your DTS-6D processor to interface to the cinema processor as indicated on the packing
list. A DTS-6D labeled “generic” will be set for platter (single projector) operation. If the DTS-6D
processor you are about to install did not come from the factory then you will must check an internal
programming jumper.
** Be sure the rear panel AC voltage switch is properly set for your mains AC supply
rating **
Remove the top cover. See Figure 1.
Programming for Two Projector (change-over) Operation
Locate the timecode board D422 (the card with the 9-pin D-connector on the rear panel and LED's on the
front). Near top center of the board there is a 7-position header called “W1”. A shunt is required vertically
over position “
0”
(farthest right position) if you are installing for change-over operation.
Programming for One Projector (platter) Operation
Locate the timecode board D422 (the card with the 9-pin D-connector on the rear panel and LED's on the
front). Near top center of the board there is a 7-position header called “W1”. No shunt is required for
platter operation. However, a shunt is supplied with each DTS-6D and this shunt should be in the “holding”
position
:
Placed horizontally across the top row.
Programming Special Functions
The D422 board contains “W1” (7-position header) that can be used for special applications. Unless specified
otherwise, all factory DTS-6D units are programmed for standard theatrical operation -- which means none
of the special functions, listed below, are used.
If a special function is required, use the table below to program the DTS-6D. To enable any of these
applications, place a shunt vertically across the position needed to perform the operation required.
“W1” Position
Special Function
0
Change-over (two timecode sources) enable
1
SMPTE
timecode enable
2
Don’t read user bits (used w/#1 enabled)
2
Nonsync program enable (when #1 not used)
4
Serial output of timecode
After the DTS-6D is programmed, reinstall top cover.
Содержание DTS-6D
