background image

60708-141

Page 1

7270-00

2.

FIRE HAZARD - Natural gas and L.P. present a hazard of
possible explosion and/or fire.

a.

Do not smoke or use open flame near the generator
set.

b.

Keep a fire extinguisher nearby and know its proper use.
Fire extinguishers rated ABC by NFPA are appropriate.

3.

DEADLY EXHAUST GAS - Exhaust fumes from any gaso-
line engine contain carbon monoxide, an invisible, odorless
and deadly gas that must be mixed with fresh air.

a.

Operate only in well ventilated areas.

b.

Never operate indoors.

c.

Never operate the unit in such a way as to allow exhaust
gases to seep back into closed rooms (i.e. through
windows, walls or floors).

4.

NOISE HAZARD - Excessive noise is not only tiring, but
continual exposure can lead to loss of hearing.

a.

Use hearing protection equipment when working
around this equipment for long periods of time.

b.

Keep your neighbors in mind when permanently install-
ing  this equipment.

5.

CLEANLINESS - Keep the generator and surrounding area
clean.

a.

Remove all grease, ice, snow or materials that create
slippery conditions around the unit.

b.

Remove any rags or other material that could create
potential fire hazards.

c.

Carefully wipe up any gas or oil spills before starting the
unit.

d.

Never allow leaves or other flammable material to build
up around the engine exhaust area.

6.

SERVICING EQUIPMENT - All service, including the
installation or replacement of service parts, should be
performed only by a qualified technician.

a.

Use only factory approved repair parts.

b.

Do not work on this equipment when fatigued.

c.

Never remove the protective guards, cover, or recep-
tacle panels while the engine is running.

d.

Use extreme caution when working on electrical compo-
nents.  High output voltages from this equipment can
cause serious injury or death.

e.

Always avoid hot mufflers, exhaust manifolds, and
engine parts.  They all can cause severe burns instantly.

f.

Installing a generator set is not a “do-it-yourself” project.
Consult a qualified, licensed electrician or contractor.
The installation must comply with all national, state, and
local  codes.

g.

Always make sure unit is disabled before placing your
hands anywhere near the fan, belts, alternator or water
hoses.

IMPORTANT SAFETY
INSTRUCTIONS

SAVE THESE INSTRUCTION

This manual contains important instructions that
should be followed during installation and maintenance
of the generator and batteries.

Read and understand all instructions in the manual
before starting and operating the generator set.

This engine generator set has been designed and manufactured
to allow safe, reliable performance.  Poor maintenance, improper
or careless use can result in potential deadly hazards;  from
electrical shock, exhaust gas asphyxiation, or fire.  Please read
all safety instructions carefully before installation or use.  Keep
these instructions handy for future reference.  Take special note
and follow all warnings on the unit labels and in the manuals.

ANSI SAFETY DEFINITIONS

************************************************************

DANGER:

DANGER indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury. This signal word
is to be limited to the most extreme situations.
***********************************************************

************************************************************

WARNING:

 WARNING indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
***********************************************************

***********************************************************

CAUTION:

CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury. It may also be
used to alert against unsafe practices.
************************************************************

NOTE:

CAUTION is also used on the unit labels and in this manual to
indicate a situation that could result in serious damage or
destruction of the equipment and possible personal injury.

1.

ELECTRIC SHOCK -  The output voltage present in this
equipment can cause a fatal electric shock. This equipment
must be operated by a responsible person.

a.

Do not allow anyone to operate the generator without
proper instruction.

b.

Guard against electric shock.

c.

Avoid contact with live terminals or receptacles.

d.

Use extreme care if operating this unit in rain or snow.

e.

Use only three-prong grounded receptacles and
extension cords.

f.

Be sure the unit is properly grounded to an external
ground rod driven into the earth.

Содержание Winpower GR27G4 B Series





















Отзывы: