DSE 5210 Скачать руководство пользователя страница 29

Страница: 29 / 49

DSE Model 5210 Automatic Start Engine Management and Instrumentation System Operators Manual

057-011 5210 OPERATING MANUAL ISSUE 5.1 18/06/2007 AM

9.1.3 PLUG “D” 4 WAY (OPTIONAL)

PIN

DESCRIPTION

CABLE

SIZE

NOTES

23 RS485

port

Common

0.5mm Use only 120

RS485 approved cable

24 RS485

port

0.5mm Use only 120

RS485 approved cable

25 RS485

port

0.5mm Use only 120

RS485 approved cable

26 Not

connected

NOTE:- Connector E is not fitted to the 5210 remote start module.

9.1.4 PLUG “F” 4 WAY

PIN

DESCRIPTION

CABLE

SIZE

NOTES

35 Generator

voltage

monitoring input

1.0mm

Connect to generator L1 output (AC)
(Recommend 2A fuse)

36 Generator

voltage

monitoring input

1.0mm

Connect to generator L2 output (AC)
(Recommend 2A fuse)

37 Generator

voltage

monitoring input

1.0mm

Connect to generator L3 output (AC)
(Recommend 2A fuse)

38 Generator

Neutral

input

1.0mm Connect to generator Neutral terminal (AC)

9.1.5 PLUG “G” 5 WAY

PIN

DESCRIPTION

CABLE

SIZE

NOTES

CT Secondary for L1

2.5mm

Connect to secondary of L1 monitoring CT

CT Secondary for L2

2.5mm

Connect to secondary of L2 monitoring CT

CT Secondary for L3

2.5mm

Connect to secondary of L3 monitoring CT

CT secondary common

2.5mm

Connect to secondary of all monitoring CT’s

43 Not

connected

9.1.6 PLUG “H” 4 WAY

PIN

DESCRIPTION

CABLE

SIZE

NOTES

Oil Pressure Input

0.5mm

Connect to Oil pressure sender

45 Coolant

Temperature

Input

0.5mm

Connect to Coolant Temperature sender

Fuel Level input

0.5mm

Connect to Fuel Level sender

Sender Common Return

0.5mm

Return feed for senders*.

NOTE*:- If using single terminal senders refer to connection diagram. If using earth return type

senders connect return terminals to pin 47 and also connect pin 47 to earth. This is detailed in the
Appendix section entitled “Sender wiring recommendations” elsewhere in this manual.

9.1.7 PC CONFIGURATION INTERFACE CONNECTOR

8-way connector allows connection to PC via the 810 configuration interface.
Module can then be re-configured utilising the

5200 series configuration

software.

9.1.8 EXPANSION

OUTPUT

CONNECTOR

The expansion connector allows connection to the 157 relay expansion module
or to the 548 LED Remote annunciator module.

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Содержание 5210


















































Результаты поиска

Содержание 5210

Отзывы:

Похожие инструкции для 5210

Бренды по названию

Популярные бренды

DSE 5210, Руководство по эксплуатации

Результаты поиска

Содержание 5210

Отзывы:

Похожие инструкции для 5210

Бренды по названию

Популярные бренды