DSE 5210 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 49

background image

DSE Model 5210 Automatic Start Engine Management and Instrumentation System Operators Manual

057-011 5210 OPERATING MANUAL ISSUE 5.1 18/06/2007 AM

41

16 APPENDIX

16.1 ALTERNATIVE WIRING TOPOLOGIES

The 5200 series controllers can support many different wiring topologies (AC systems) to suit the many systems in
use world-wide. The ‘Typical connection diagram’ details how to connect the module when used in a 3 phase, 4
wire system (3 phase star connected alternators). Changes to this typical wiring diagram for other AC systems are
detailed below.

NOTE:- The factory default configuration for the 5210 module is for use with the 3 phase, 4 wire AC

system. If another system is to be used, the controller must be reconfigured using the 5200 series
configuration software.

16.1.1 3 PHASE, 3 WIRE

The alternator is 3 phase delta connected. Phases are separated by 120

°

16.1.2 1 PHASE, 2 WIRE

Single phase alternator with neutral conductor.

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

«
...
39
40
41
42
43
...
»

Содержание 5210


















































Отзывы:

Нет отзывов

Похожие инструкции для 5210

Бренд: K&K Страницы: 6

Бренд: IBM Страницы: 144

Бренд: ZIMO Страницы: 38

Бренд: Eaton Страницы: 100

Бренд: Haldex Страницы: 8

Бренд: ValvTechnologies Страницы: 20

FSDrive-MV1000 Series

Бренд: YASKAWA Страницы: 260

Бренд: YASKAWA Страницы: 114

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 152

Бренд: YASKAWA Страницы: 66

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA Страницы: 58

Бренд: Haes Страницы: 42

Бренд: CORNING Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды