FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by
Digital Security Controls could void your authority to use this
equipment. This equipment generates and uses radio frequency energy
and if not installed and used properly, in strict accordance with the
manufacturer's instructions, may cause interference to radio and
television reception. It has been type tested and found to comply with
the limits for Class B device in accordance with the specifications in
Subpart "B" of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference in any residential
installation. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
interference to television or radio reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control
and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced
radio/television technician for additional suggestions. The user may
find the following booklet prepared by the FCC helpful: "How to
Identify and Resolve Radio/Television Interference Problems". This
booklet is available from the U.S. Government Printing Office,
Washington, D.C. 20402, Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of
this equipment is a label that contains, among other information, the
FCC registration number and ringer equivalence number (REN) for this
equipment. If requested, this number must be provided to the
Telephone Company.
3G3070 Product IdentifierUS: F53MO00B3G3070
REN:0.0B
USOC Jack:RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to
be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line may
result in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0).
To be certain of the number of devices that may be connected to a line,
as determined by the total RENs, contact the local Telephone
Company. For products approved after July 23, 2001, the REN for this
product is part of the product identifier that has the format. US:
AAAEQ##TXXXX. The digits represented by ## are the REN without
a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN
is separately shown on the label.
Incidence of Harm
If this equipment 3G3070 causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice is not
practical, the Telephone Company will notify the customer as soon as
possible. Also, you will be advised of your right to file a complaint with
the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities,
equipment, operations or procedures that could affect the operation of
the equipment. If this happens the Telephone Company will provide
advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment for repair or warranty
information, please contact the facility indicated below. If the
equipment is causing harm to the telephone network, the Telephone
Company may request that you disconnect the equipment until the problem
is solved. This equipment is of a type that is not intended to be repaired by
the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation
commission for information.
Alarm dialling equipment must be able to seize the telephone line and place
a call in an emergency situation. It must be able to do this even if other
equipment (telephone, answering system, computer modem, etc.) already
has the telephone line in use. To do so, alarm dialling equipment must be
connected to a properly installed RJ-31X jack that is electrically in series
with and ahead of all other equipment attached to the same telephone line.
Proper installation is depicted in the figure below. If you have any
questions concerning these instructions, you should consult your telephone
company or a qualified installer about installing the RJ-31X jack and alarm
dialling equipment for
you.
Industry Canada Compliance Statement
This Equipment meets the applicable Industry Canada Terminal Equipment
Technical Specifications. This is confirmed by the registration number.
The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity
indicating that Industry Canada technical specifications were met. It does
not imply that that Industry Canada approved the equipment. The Ringer
Equivalence Number (REN) for this terminal equipment is 0.0. The REN
assigned to each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination
of devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all devices does not exceed 5.
Cet équipement est conforme aux spécifications techniques applicables aux
équipements terminaux d'Industrie Canada. Ceci est confirmé par le
numéro d'enregistrement. L'abréviation IC précédant le numéro
d'enregistrement signifie que l'enregistrement a été effectué sur la base de
la Déclaration de conformité indiquant que le produit est conforme aux
spécifications techniques d'Industrie Canada. Ceci n'implique pas que le
produit ait été approuvé par Industrie Canada.
Le nombre équivalent de sonneries (REN) de cet appareil terminal est 0.0.
Le REN attribué à chaque équipement terminal fournit une indication sur
le nombre maximum de terminaux pouvant être connectés sur une interface
téléphonique. La terminaison sur une interface peut constituer en n'importe
quelle combinaison d'appareils, à la condition seulement que la somme des
Nombres équivalents de sonneries de tous les appareils ne soit pas
supérieure à 5.
This Class B digital apparatus meets all requirements of the Canadian
interference-causing equipment regulations. Cet appareil numérique de la
Classe B respecte toutes les exigences de règlement sur le matériel
brouilleur du Canada.
The term “IC:” before the radio certification number only signifies
that Industry Canada technical specifications were met.
WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20cm
or more must be maintained between the antenna of this device and persons during device operation.
Содержание 3G3070
Страница 2: ......
