DSC 3G2060, Руководство по установке

Страница: 34 / 48

30
Ethernet/Cellular Programming Worksheets 3G Alarm Communicator Installation Manual
System Options
[001] Ethernet IP Address
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____|____|____|____|
[002] Ethernet IP Subnet Mask
Default (255.255.255.000)
|____|____|____||____|____|____||____|____|____|____|____|____|
[003] Ethernet Gateway IP Address
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____|____|____|____|
[004] Receiver Supervision Interval
Default (0087/135). Valid range: 0000 - FFFF.
|____|____|____|____|
[005] System Toggle Options
|____| [1] Ethernet Receiver 1 Supervised Default (OFF).
|____| [2] Cellular Receiver 1 Supervised Default (OFF).
|____| [3] Supervision Type Default (OFF).
|____| [4] Primary Communications Path. Default (ON - 3G2060).
|____| [5] Redundant Communications Default (OFF).
|____| [6] Remote Firmware Upgrade Default (ON).
|____| [7] Alternate Test Transmission Default (OFF).
|____| [8] Cellular Low Signal Trouble Default (OFF).
[006] System Toggle Options 2
|____| [1] Ethernet Receiver 1 Enabled Default (ON).
|____| [2] Ethernet Receiver 2 Enabled Default (ON).
|____| [4] Cellular Receiver 1 Enabled Default (ON).
|____| [5] Cellular Receiver 2 Enabled Default (ON).
|____| [7] DLS Over Cellular Default (ON).
[007] DNS Server IP 1
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____|____|____|____|
[008] DNS Server IP 2
Default (000.000.000.000)
|____|____|____||____|____|____||____|____|____|____|____|____|
Programming Options
[011] Installer Code
Default (CAFE). Valid range: 0000 - FFFF.
|____|____|____|____|
[012] DLS Incoming Port
Default (0BF6/3062). Valid range: 0000 - FFFF.
|____|____|____|____|
[013] DLS Outgoing Port
Default (0BFA/3066). Valid range: 0000 - FFFF.
|____|____|____|____|
[022] Communications Format
Default (04). Program 03 (CID), 04 (SIA).
|____|____|
[023] Panel Absent Trouble
Default (FF). Program 00 disable or FF enable.
|____|____|
[024] Panel Absent Trouble Restore
Default (FF). Program 00 disable or FF enable.
|____|____|
[025] Radio Activation Restore
Default (FF). Program 00 disable or FF enable.
|____|____|
System Test Options [026 - 029]
[026] Ethernet 1 Transmission
Default (FF). Program 00 disable or FF enable.
|____|____|
[027] Ethernet 2 Transmission
Default (00). Program 00 disable or FF enable.
|____|____|
[028] Cellular 1 Transmission
Default (FF). Program 00 disable or FF enable.
|____|____|
[029] Cellular 2 Transmission
Default (00). Program 00 disable or FF enable.
|____|____|
[030] FTC Restore
Default (FF). Program 00 disable or FF enable.
|____|____|
[033] Communicator Firmware Update
Begin
Default (FF). Program 00 disable or FF enable.
|____|____|
E
THERNET
/C
ELLULAR
P
ROGRAMMING
W
ORKSHEETS