DSC 3G2055 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 52

DSC 3G2055 Скачать руководство пользователя страница 9

9

C24 C

OMMUNICATIONS

™

1

A

CCOUNT

AND

SIM

CARD

A

CTIVATION

(Before Installation)
Installation of the Communicator requires activation with Connect24 before opera-
tion. Dealer application forms and additional information on the Connect24 Voice
Response Unit (VRU) and graphical user interface (GUI) can be found at

http://

www.Connect24.com

or by telephone at: USA 1-888-251-7458 or CANADA 1-888-

955-5583.

IMPORTANT:

Prior to installing a

3G2055 or TL2553G

Communicator, contact your

monitoring station to determine if it is a master re-seller or visit http://www.Con-
nect24.com to become an authorized dealer. In either instance, you will require a Pro-
file Number, Installer ID Number, and an Installer Password. Perform the following
pre installation:

1. Retrieve the installer account and password from the master reseller, or from

Connect24 directly.

2. Connect your browser to the Connect 24 website at:

http://

www.Connect24.com

or use the mobile website m.connect24.com.

3. Log in to the Connect24 website using your installer account and password.

4. Perform the following steps in a Connect24 session to activate the SIM card and

initialize programming:

a. Navigate to the

Initialize an account

section.

b. Select

Profile

(This information will be provided by the master reseller or by

Connect24).

c. Select

Product

Module.

d. Enter the SIM card number.
e. Click

Next

then enter in all relevant information as required.

f. Confirm all information is entered correctly before submitting.

5. Repeat Step 4 to program another SIM card (i.e. another Subscriber), or log out

from Connect24.

6. When you are at the physical installation site, the Communicator will automatically

connect and download its programming from Connect24 once the unit is
initialized.

NOTE: Following initial installation, you can log in to the Connect24 website at any
time to re-configure the Communicator remotely, using the account created for this
installation. For more information, refer to the Connect24 website.

Before leaving the installation site, the Communicator TL2553G shall be
connected via an APPROVED (acceptable to the local authorities) Network
Interface Device (NID) (e.g., for UL Installations, U60950 listed NID). All wiring
shall be performed according to the local electrical codes.

E

NCRYPTION

The Communicator uses 128 Bit AES Encryption. Encryption can only be enabled
from the monitoring station receiver. Each receiver can independently have encryp-
tion enabled or disabled. When encryption is enabled, the central station will config-

C

OMMUNICATOR

P

RE

I

NSTALLATION

C

ONFIGURATION

1.

Connect24

,

DSC

, and

DLS IV

are Registered Trademarks of Tyco International Ltd. and its respective Com-

panies. All Rights Reserved.

«
...
7
8
9
10
11
...
»

Содержание 3G2055





















































Отзывы:

Нет отзывов