manualshive.com logo in svg

DSC 3G2055, Руководство по установке, Страница: 18 / 52

Поделиться
Скачать
DSC 3G2055 Скачать руководство пользователя страница 18

18

[7]

 

Alternate Test Transmissions

Default (OFF).

ON

: When the periodic test transmission interval occurs, the test transmission will

alternate between being sent to the primary and secondary receivers with each test
transmission interval.

OFF

: When the periodic test transmission interval occurs, the test transmission will

be sent to the programmed receivers, based on the settings of the periodic test
transmission reporting codes.

[8]

 

Cellular Low Signal Trouble

.

Default (OFF)

This option masks the Low Signal trouble from the Cellular trouble event.

ON

: A Cellular Trouble event is transmitted to receiver when the radio signal level falls

below threshold level (average CSQ level is 4 or less).

OFF:

 A Cellular Trouble event is 

not

 transmitted to receiver when the radio signal

level falls below threshold level (average CSQ level is 4 or less).

[006] System Toggle Options 2
[1] 

Ethernet 1 Receiver Enabled.

Default (ON) (OFF for 

3G2055

).

ON

: Ethernet Receiver 1 is enabled.

OFF

: Ethernet Receiver 1 is disabled.

[2] 

Ethernet 2 Receiver Enabled.

Default (ON) (OFF for 

3G2055

).

ON

: Ethernet Receiver 2 is enabled.

OFF

: Ethernet Receiver 2 is disabled.

[3] Reserved.

 ( ).

[4] 

Cellular 1 Receiver Enabled.

Default

 (ON).

ON

: Cellular Receiver 1 is enabled. 

OFF

: Cellular Receiver 1 is disabled.

[5] 

Cellular 2 Receiver Enabled.

Default

 (ON).

ON

: Cellular Receiver 2 is enabled.

OFF

: Cellular Receiver 2 is disabled.

[6]

 

Reserved

 ( ).

[7]

 

DLS Over Cellular.

Default (

ON

).

NOTE: Program this toggle as OFF if you want to completely disable DLS from using 
the Cellular path.

ON

: DLS is enabled on the Cellular path.

OFF

: DLS is disabled on the Cellular path.

NOTE: If this Toggle is OFF, DLS sessions will occur on the Ethernet path only, 
regardless of Primary Path set in Section [005] Toggle Option [4]. If it is ON then the 
Communicator will connect to the Primary path first for DLS and if the session fails, 
the Secondary path will be used.

[8]

 

Trouble Suppression

 

Default (OFF)

ON: 

GSM, Ethernet and Receiver Supervision Trouble and Restore conditions will be

delayed for the time period programmed in section [226]. After the delay expires the
trouble conditions will be indicated and communicated.

OFF: 

GSM, Ethernet and Receiver Supervision Troubles will be immediately indicated

and communicated.

Содержание 3G2055





















































Отзывы:

Нет отзывов