Droplet UHSAS Скачать руководство пользователя страница 48

Страница: 48 / 56

Manual, Ultra High Sensitivity Aerosol Spectrometer (UHSAS)

DOC-0210 Rev E-4

4 8

12.0

Configuration Tab

This tab displays the instrument configuration parameters. Note that some of these parameters

are protected and cannot be changed unless the user logs in by typing a password in the

Password

field and then clicking on the

Enter Password

button. To revert to normal operation

(i.e., not a password-protected mode), click on the

Revert Mode

button. Figure 29 shows the

Configuration

tab in Calibration mode.

Clicking on

Revert to Factory Configuration

reverts all the parameters to their original default

values. These parameters are stored in separate configuration file,

factory.ini

, which

should not be modified.

The

Configuration File Date

field lists the date the configuration file was last modified in

YYYYMMDD format.

Clicking the

Save

button saves the present instrument configuration to a file. When this button

is clicked, the system will prompt the user for a file name. The file must be saved in the directory

C:\DMT\Spectrometer Support.

As stated above, the factory provided configuration

file,

factory.ini

, should not be overwritten.

Figure 29: Configuration Tab

Содержание UHSAS

























































Результаты поиска

Содержание UHSAS

Отзывы:

Бренды по названию

Популярные бренды

Droplet UHSAS, Руководство оператора

Результаты поиска

Содержание UHSAS

Отзывы:

Бренды по названию

Популярные бренды