Droplet UHSAS Скачать руководство пользователя страница 3

Страница: 3 / 56

Manual, Ultra High Sensitivity Aerosol Spectrometer (UHSAS)

DOC-0210 Rev E-4

Laser Safety Warnings

STRICT OBSERVANCE OF THE FOLLOWING LASER SAFETY LABELS IS ADVISED.

The UHSAS is a Class I Laser Product with an embedded Class 4 pump laser. CAUTION: Use of

control or adjustments or performance of procedures other than specified in this manual may

result in hazardous radiation exposure.

The above certification and identification labels are located on the back panel.

This label is located on the support structure

underneath the instrument cover, identifying the

location of the two laser safety interlocks.

This label is located in two locations on the optical block and the

arrow points to the cleaning ports.

This label is located on the optics block.

Laser Characteristics

Class 1

Laser Product

Complies with 21 CFR

1040.10 and 1040.11 except

for deviations pursuant to

Laser Notice no. 50, dated

June 24, 2007

Содержание UHSAS

























































Результаты поиска

Содержание UHSAS

Отзывы:

Бренды по названию

Популярные бренды

Droplet UHSAS, Руководство оператора

Результаты поиска

Содержание UHSAS

Отзывы:

Бренды по названию

Популярные бренды