manualshive.com logo in svg

DriSteem Vapor-logic 4, Инструкция по установке и эксплуатации

Поделиться
Скачать
DriSteem Vapor-logic 4 Скачать руководство пользователя страница 75

%3*45&&. 7BQPSMPHJD *OTUBMMBUJPO BOE 0QFSBUJPO .BOVBM t 1BHF 

Operation

Trim tanks

A tank functioning as a trim tank is assigned to priority group 0 
and always operates before tanks in priority groups 1, 2, or 3. 

The function of a trim tank is to be the first tank in a multi-tank 
group to respond to system demand changes. Multi-tank groups 
requiring a rapid response to changes in system demand typically 
have an electric element humidifier with SSR control as the trim 
tank.

Redundant tanks 

The system capacity of a multi-tank group is the combined capacity 
of tanks in groups 0, 1, and 2. A tank functioning as a redundant 
tank is assigned to priority group 3 and operates only if one or 
more of the tanks in groups 0, 1, or 2 is not available and the multi-
tank group cannot meet the demand for steam production. Placing 
a tank in priority group 3 ensures that it only runs as a redundant 
tank.

Because a redundant tank operates infrequently, assigning master 
controller status to the redundant tank in a multi-tank group 
reduces system down time while the master controller tank receives 
servicing.

Tank wear leveling

The master controller monitors tank wear and assigns steam 
production to tanks to equalize wear as much as possible within 
the multi-tank group. 

Fault tolerance

All tanks in a multi-tank group periodically send a status message 
to all other tanks in the multi-tank group. If this message is not 
received by the other tanks within a defined time period, the tank 
is assumed to be unavailable to the remaining tanks in the group. 
The newly unavailable tank will be taken off the list of available 
tanks and the system will respond appropriately. If the unavailable 
tank is the master controller, the remaining slaves will continue to 
run for a short time at the level they were last told to run, and then 
quit.

M u l t i p l e - t a n k   o p e r a t i o n

Priority groups

Vapor-logic4 assigns humidifiers a priority 
group number. These numbers identify tank 
function as follows:

0 = Trim tank
1 = Default tank configuration
3 = Redundant tank

Note that Priority Group 2 is currently 
unassigned.

Содержание Vapor-logic 4

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды