background image

- 12 -

 

 

2.4

 

ELECTRICAL INSTALLATION 

2.4.1

 

GENERAL INFORMATION FOR ELECTRICAL INSTALLATION 

Perform  the  connection  according  to  the  scheme.  Factory  connection  must  not  be  changed!  (Figure  8). 
The degree of protection of electric parts of the heater is IP 44. The power input of electric element is 2.000 W 
(OKHE ONE/E 50 - 120), 1.100 W (OKHE ONE/E 30). 

 

 

 

 

 

 

 

 

 

 

 

Figure 8 

It is necessary to observe the below requirements during the electric wiring. 

 

The wiring diagram is attached to the heater on the side of the electric installation cover 
(Figure 8). 

 

The electric installation may only be connected, repaired and inspected only by a person 
authorized to perform that activity. 

 

Professional  connection  must  be  confirmed  on  the  warranty  card,  or  supported  by 
another document. 

 

The heater is connected to 230V/50Hz power supply by a fixed movable cable (depending 
on the connection method).  

 

When  installing  in  bathrooms,  laundry  rooms,  rest  rooms  and  showers,  it  is  necessary 
to follow the relevant standard. 

 

The degree of protection of electric parts of the heater is IP 44. 

 

Adhere to the protection against electric shock according to the standard 

 

If the supply cord is damaged, it must be replaced by a company (person) authorized to such 
activity in order to avoid a hazard. 
 

 

 

Содержание OKHE ONE/E 120




















Отзывы: