Dr. Mach Mach 130 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 48

background image

Ceiling and wall attachment

Dr. Mach

Lamps and Engineering

7. Mounting the lamps

Attention!
Each lamp has a red sticker applied near the
coupling journal at the lamp bow or cardanic
bow. The sticker shows the rated voltage of the
lamp.
Connect the lamp only to the prescribed volt-
age, to avoid irreparable damage (e.g. the elec-
tronical components).

Following rated voltage is usual:

After mounting the lamp take off the sticker and
dispose it, otherwise it could fall down in the
OT-field after some time!

Coupling journal

Sticker with voltage
information

Lamp bow or
cardanic bow

22,8 V

110 V

120 V

230 V

When mounting the lamp and also at one-yearly intervals, a light coat of acid-free grease should be ap-
plied to the mounting journal and the journal groove F of the lamp, or possibly the already existing cardan
bow.

Caution:

The lamp may only be dismounted (in reverse order to the mounting procedure) after the mount-
ing safeguard has been positioned and screwed tight, as the arm is under spring tension.

Never let the spring arm bounce up!

7.1 Mounting at the standard spring arm

7.1.1 Preparatory work

Attention!
Disconnect the on-site power supply and pro-
tect it from being switched on again.

•

Disconnect the equipment / pull out the power
plug and protect the equipment from being
switched on again.

Attention!
Danger of injury: When it is pressed down, the
spring arm can jump up suddenly and cause
injury.
During the installation of the lamp / device, do
not allow anyone to be within the swivelling
range of the spring arm.

•

Remove the recessed head screw

1

and slide

the sleeve

2

up.

•

Remove the securing segment

3

with a small-

bladed screw driver.

•

Remove the protective cap

4

from the mount-

ing.

2

1

3

4

59500001

Edition 06

11.03.2003 / Bak Page 30/48

«
...
28
29
30
31
32
...
»

Содержание Mach 130

















































Отзывы:

Нет отзывов

Похожие инструкции для Mach 130

Бренд: Rabe Страницы: 65

Бренд: YSI Страницы: 70

Бренд: jcb Страницы: 41

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: Danelec Страницы: 67

Бренд: Unitary products group Страницы: 28

Бренд: RayLight Страницы: 34

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: Latham Страницы: 19

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды