manualshive.com logo in svg

Douglas Dynamics SnowEx Liqui Maxx, Руководство пользователя и инструкции по установке, Страница: 25 / 40

Поделиться
Скачать
Douglas Dynamics SnowEx Liqui Maxx Скачать руководство пользователя страница 25

Lit. No. 76348, Rev. 01 

25 

May 15, 2017

NOTE: UNITS (English or Metric) must be set in 

"Special" Calibrate before any other CALIBRATE 

or "SPECIAL" CALIBRATE values.

There are three (3) pages of "SPECIAL" CALIBRATE 

values, total of 18 used for Standard Drive, selected 

by the rotary switch and BLAST key. To enter Special 

Cal, put the system in HOLD, turn the console power 

OFF, press and hold the BLAST button while turning 

console ON. The console will display SPEC for 

2 seconds to show that the console is in the Special 

Calibration mode. Release the BLAST button.

If the Console is unlocked, the Warning LED will 

also turn ON and any of the "Special" CALIBRATE 

values can be adjusted.

If the Console is locked, the Warning LED will not 

turn ON and the "Special" CALIBRATE values can 

only be viewed and cannot be adjusted.

NOTE: Press and release the BLAST key to 

alternate between SPECIAL CAL pages 1, 2, and 3 

(Number icons indicate page).

The desired Special Calibration Parameter(s) can then 

be accessed with the rotary switch. To exit Special 

Calibration, press and hold the BLAST button for 

1 second. The console will save any changes and 

revert to normal operation.

To exit without saving changes, simply turn the 

console power OFF without pressing BLAST.

"SPECIAL" CALIBRATION

Entering Calibration Values

WIDTH

CAL

FLOW

CAL

MIN

FLOW

ADJUST

RATE

TARGET

RATE

SPEED

CAL

TEST

SPEED

VOLUME /

MINUTE

DISTANCE

(1) (2) (3)

MODE

(ALARM RESET)

VOLUME

(1) (2) (3)

RATE

SPEED

(1) (2) (3)

 AREA

(1) (2) (3)

TANK LEVEL

BLAST

AUTO

MAN

RESET

MODE

SELECT

CAL

1

 Special Calibration

Special Cal

Page 3

Special Cal

Page 2

Special Cal

Page 1

Manual

Enable

Minimum 

Alarm 

Speed

Fill Tank

Size

Start

Time

Tank Alarm

Set Point

Auto

Shutoff

Blast

Duration

Alarm

Enable

Auto Delay

Time

Blast

Target Rate

Special Cal

Page 1

Special Cal

Page 2

Special Cal

Page 3

Units

(Eng/Metric)

Set Year

Vehicle

Number

Set Month

Valve

Polarity

Set Date

Valve

Speed

Set Time

OPERATING AND CALIBRATION INSTRUCTIONS

Содержание SnowEx Liqui Maxx









































Отзывы:

Нет отзывов