Dorner 62M005ESBDDEN Скачать руководство пользователя

Страница: 19 / 20

851-738 Rev. A

Dorner Mfg. Corp.

Brushless DC Motor Control

Service Parts

Brushless DC Motor Control

NOTE

For replacement parts other than those shown in this section, contact an authorized Dorner Service Center
or the factory. Key Service Parts and Kits are identified by the Performance Parts Kits logo

. Dorner

recommends keeping these parts on hand.

Item Part

Number

Description

63MBD11B60

Controller, 115 Volts, 60 Watts

63MBD23D60

Controller, 230 Volts, 60 Watts

63MBD11B200

Controller, 115 Volts, 200 Watts

63MBD23B200

Controller, 230 Volts, 200 Watts

807-2190

Cord Cover

920416M

Socket Head Screws, M4-0.70x16 (x4)

350292

Mounting Bars (x2)

639971MK10

T-Bar, Single Drop-In (x10)

920616M

Socket Head Screws, M6-1.00x16 (x2)

Содержание 62M005ESBDDEN





















Результаты поиска

Содержание 62M005ESBDDEN

Отзывы:

Похожие инструкции для 62M005ESBDDEN

Бренды по названию

Популярные бренды

Dorner 62M005ESBDDEN, Инструкция по установке, эксплуатации и запасным частям

Результаты поиска

Содержание 62M005ESBDDEN

Отзывы:

Похожие инструкции для 62M005ESBDDEN

Бренды по названию

Популярные бренды