ESA - II
Service-Key
Operation via PDA
Software update of
ESA-II
control unit via service key
The software update may not be done while the door is under operation, as it could get out of
control.
Following a software update, the power supply must be reset (battery pack and power plug must be
removed for a short time) and a learning cycle has to be performed. The door settings must be
checked and reset if required (e.g. locking type, motor type, operation via battery pack etc.).
Locking the control panel via service key.
LED status indicator
LED status indicator
Update PDA service key
Update SK control unit
Troubleshooting
The system cannot be updated via infrared device.
The service key is the linking element between the PDA (Personal Digital Assistant) and the
control
unit. It may also be used with the control unit without PDA in order to disable the control keys of the control unit or
to update the software of the control unit.
The PDA is connected to the service key (9-pole SUB D plug) with a serial connecting cable. Connect the service
key via the connecting cable to the control unit (Port 13 behind the service keys). Establish a connection between
the controller and the PDA (see ASP operating instructions). The LED status indicator on the service key turns
green. Now the settings may be changed via the PDA. An upload must be performed in case that any settings
have been changed. The LED status indicator of the service key lights red, in the event, that an error occurs during
upload. In this case the upload must be repeated. If the upload was successful, the LED is green. The PDA may
also be used to install a new software version on the service key. Software upload from PDA to service key: See
"ESA" ASP data base recording.
The service key must contain the latest software version.
Take the
sliding door out of operation (set Program switch to CLOSE, or use the EMERGENCY OFF
push buttonif necessary.) Press and hold the start push button for three seconds. The LED status indicator on the
service key
s orange while it performs the update. It
s red in the event that an error occurs during
upload. In this case, the upload must be repeated. If the upload was successful, the LED turns green.
If the control panel of the
control system is locked, the service key unlocks it, by connecting it.
The settings can now be changed. As soon as the service key is disconnected from the control unit, the control
panel is locked automatically.
l
u
f
s
s
e
c
c
u
s
e
t
a
d
p
U
l
u
f
s
s
e
c
c
u
s
e
t
a
d
p
U
n
e
e
r
G
s
s
e
r
g
o
r
p
n
i
e
t
a
d
p
U
e
g
n
a
r
O
e
t
a
d
p
u
g
n
ir
u
d
r
o
r
r
E
d
e
R
Orange
Red
The control unit indicates an error code in the event of an incomplete update.
The LED status indicator on the service key goes out.
m
e
t
s
y
S
1
0
e
c
n
e
u
q
e
s
m
a
r
g
o
r
P
3
0
r
o
r
r
e
M
A
R
5
0
d
e
n
if
e
d
t
o
n
r
o
t
c
e
V
t
p
u
r
r
e
t
n
I
7
0
k
c
e
h
c
-
M
A
R
5
1
)
g
n
i
m
i
T
-
W
C
D
(
e
c
n
e
u
q
e
s
r
e
l
d
n
a
H
k
c
o
l
C
-
S
O
M
D
1
3
Bootloader CRASH
ROM checksum error
ESA - II
ESA - II
ESA - II
Update in progress
Error during update
y
a
l
p
s
i
d
r
o
r
r
E
s
n
o
s
a
e
r
e
l
b
i
s
s
o
P
e
d
o
c
r
o
r
r
E
Should one of the above-mentioned errors occur, the system must be disconnected from power supply and the ES 200 control
unit has to be programmed again.
ESA II Controller
and Wiring Manual
DORMA
28
DORMA AUTOMATICS, Inc.
924 Sherwood Drive
Toll-Free: 877-367-6211
DL2842-010
Lake Bluff, IL 60044
Fax: 877-423-7999
rev. A
E-mail: [email protected]
Subject to change without notice
