Dorma ESA II Скачать руководство пользователя страница 4

Страница: 4 / 29

1. Commissioning

1.1

Please note:

Work on electrical equipment may only be

performed by properly qualified electricians.

Power supply (by others) with 15 A fuse protection

must be available.

Power cord must be double-insulated, for example:

Do not use ribbon cable! The maximum cable length

of the external components must not exceed 98 ft.

1.2

Basic requirements:

The operator is fully assembled.

The protective earth is connected.

The safety beams are connected (optional).

The rechargeable battery pack (optional

is connected.

Components supplied separately, such as

program panel, activators, radar motion

detectors, Night-/Bank key switches and

connected.

The end stops are adjusted so that, at maximum

opening with, both active leaves are in contact

with the stops; and when door is closed, neither

panel touches the sealing profile.

The door has to run smoothly.

1.3

Commissioning

Open the sliding leaves half way.

Move the program switch to position

Insure jumper is in place on the breakout or

emergency stop contacts

The door must perform a closing cycle at low

(creep) speed.

If the door performs an opening cycle, the

system must be set back to original settings.

Disconnect the power plug so that the

opening cycle stops.

Proceed on 1.5 original settings

If the door performs a closing cycle, proceed with the

learning cycle starting with the door closed.

Please note:

The safety beams and radar motion detectors are

disabled during the learning cycle, as it has to be

performed without interruptions.

In case that a fault or error should occur during this

procedure, the learning cycle will be interrupted

needs to be re-started.

1.4

Performing the learning cycle:

Press SERVICE/SELECT button until one of the

external until each one of the display

illuminates in turn.

The door accelerates in order to determine the

door weight.

The door opens at low (creep) speed to determine

the opening width.

The opening parameters are now stored and an

8 flashes twice on the 7-segment display.

The learning cycle is now complete.

The 7-segment display indicates a dot.

The door closes at normal speed.

Test of opening cycle

Set program switch to AUTOMATIC and push the

SERVICE/SELECT button

The door performs an opening cycle and is

closed after the hold-open time expires.

The following door parameters must be checked

and amended if required.

Settings: See operating instructions of adjustment.

Perform amendments with the aid of the parameterization

instructions and the 7-segment display on the control unit

or via PDA.

Menu A.:

Emergency operation (via rechargeable battery pack)

- original settings = 0

Menu r.:

Locking action depending on position of program switch

- original settings = 1

Menu L.:

Locking type original settings = 1

The locking type is not learned automatically during the learning cycle.

1.5

General information concerning the original settings.

If several settings have been changed, the door no longer

works properly, reset to original settings

Set program switch to

Open the door leaves to 50%

Connect power plug.

Press and hold the service key.

As soon as the power supply has been switched on,

the control unit powers up and the security checks are

performed.

An 8 is shown on the seven-segment display. When the

8 blinks twice, the original settings have been restored.

In case the door starts an opening cycle, press the minus

button on the control unit to change the direction of the motor.

Following the restoring of the original settings, differing

settings (e.g. locking type) have to be made manually either

via the buttons on the control unit or via the PDA

(parameterization) and a learning cycle has to be performed

(see 1.4)

ESA II Controller

and Wiring Manual

DORMA

DORMA AUTOMATICS, Inc.

924 Sherwood Drive

Toll-Free: 877-367-6211

DL2842-010

Lake Bluff, IL 60044

Fax: 877-423-7999

rev. A

E-mail: [email protected]

Subject to change without notice

Содержание ESA II






























Результаты поиска

Содержание ESA II

Отзывы:

Похожие инструкции для ESA II

Бренды по названию

Популярные бренды

Dorma ESA II, Руководство пользователя

Результаты поиска

Содержание ESA II

Отзывы:

Похожие инструкции для ESA II

Бренды по названию

Популярные бренды