Doosan 10/215HA, Руководство по эксплуатации и техническому обслуживанию

Страница: 41 / 68

MAINTENANCE 39
9/235HA, 10/215HA
COMPRESSOR OIL FILTER
Refer to the SERVICE/MAINTENANCE CHART in this section for the
recommended servicing intervals.
Removal
Clean the exterior of the filter housing and remove the spin-on element
by turning it in a anticlockwise direction.
Inspection
Examine the filter element.
Reassembly
Clean the filter gasket contact area and install the new element by
screwing in a clockwise direction until the gasket makes contact with
the filter housing. Tighten a further
1
/
2
to
3
/
4
of a revolution.
COMPRESSOR OIL SEPARATOR ELEMENT
Refer to the SERVICE / MAINTENANCE CHART in this section for
service intervals.
Removal
Disconnect all hoses and tubes from the separator tank cover plate.
Remove the drop-tube from the separator tank cover plate and then
slide the cover plate towards the airend. Remove the separator
element.
Inspection
Examine the filter element. Examine all hoses and tubes, and replace
if necessary.
Reassembly
Thoroughly clean the orifice/drop tube and install a new o-ring before
reassembly. Install the new element.
Reposition the cover plate, taking care not to damage the o-ring, and
replace the cover plate screws tightening in a criss-cross pattern to the
recommended torque (refer to the TORQUE SETTING TABLE later in
this section).
Replace the drop-tube and reconnect all hoses and tubes to the
separator tank cover plate.
Replace the compressor oil (refer to LUBRICATION later in this
section).
COMPRESSOR OIL COOLER AND ENGINE RADIATOR AIR
CHARGE COOLER
When grease, oil and dirt accumulate on the exterior surfaces of the oil
cooler and radiator, the efficiency is impaired. It is recommended that
each month the oil cooler and radiator be cleaned by directing a jet of
compressed air, (carrying if possible a non-flammable cleaning
solvent) over the exterior core of the cooler/radiator. This should
remove any accumulation of oil, grease and dirt from the exterior core
of the cooler so that the entire cooling area can radiate the heat of the
lubricating and cooling oil/water into the air stream.
WARNING: Do not remove the filter(s) without first making sure
that the machine is stopped and the system has been
completely relieved of all air pressure.
(Refer to STOPPING THE
MACHINE in the OPERATING INSTRUCTIONS section of this
manual).
CAUTION: If there is any indication of the formation of varnishes,
shellacs or lacquers on the filter element, it is a warning that the
compressor lubricating and cooling oil has deteriorated and that it
should be changed immediately. Refer to LUBRICATION later in this
section.
CAUTION: Start the machine (refer to PRIOR TO STARTING and
STARTING THE MACHINE in the OPERATING INSTRUCTIONS
section of this manual) and check for leakage before the machine is
put back into service.
WARNING: Do not remove the filter(s) without first making sure
that the machine is stopped and the system has been
completely relieved of all air pressure.
(Refer to STOPPING THE
MACHINE in the OPERATING INSTRUCTIONS section of this
manual).
CAUTION: Start the machine (refer to PRIOR TO STARTING and
STARTING THE MACHINE in the OPERATING INSTRUCTIONS
section of this manual) and check for leakage before the machine is
put back into service.
WARNING: Hot engine coolant and steam can cause injury.
When adding coolant or antifreeze solution to the engine
radiator, stop the engine at least one minute prior to releasing
the radiator filler cap. Using a cloth to protect the hand, slowly
release the filler cap, absorbing any released fluid with the cloth.
Do not remove the filler cap until all excess fluid is released and
the engine cooling system fully depressurised.
WARNING: Follow the instructions provided by the antifreeze
supplier when adding or draining the antifreeze solution. It is
advisable to wear personal protective equipment to prevent skin
and eye contact with the antifreeze solution.