background image

ENGINE INSTRUCTION MANUAL

21

 

9/235HA, 10/215HA

FUEL, LUBRICANTS AND COOLANT

FUEL

Fuel selection

The following properties are required of the diesel fuel:

Must be free from minute dust particles.

Must have adequate viscosity.

Must have high cetane value.

Must have high fluidity at low temperature.

Must have low sulphur content.

Must have low residual carbon.

It  is  strongly  advisable  to  use  ASTM  D975  No.  2D  (the  general
automotive  diesel  engine  purpose  fuel  oil)  or  equivalent  which  fully
meets the above requirements.

Fuel requirements

To help avoid fuel system or engine damage, please read the following:

Do not use diesel fuel which has been contaminated with engine oil.
Besides  causing  engine  damage,  such  fuel  can  also  affect  emission
control. Before using any diesel fuel, check with the fuel supplier to see
if the fuel has been mixed with engine oil.

Your  engine  is  designed  to  use  either  Number  1-D  or  Number  2-D
diesel fuel. However, for better fuel economy, use Number 2-D diesel
fuel  whenever  possible.  At  temperatures  less  than  -7°C,  (20°F),
Number  2-D  fuel  may  pose  operating  problems  (see  “Cold  weather
operation” which follows). At colder temperatures, use Number 1-D fuel
(if available) or use a “winterized” Number 2-D (a blend of Number 1-D
and Number 2-D). This blended fuel is usually called Number 2-D also,
but can be used in colder temperatures than Number 2-D fuel which
has not been “winterized.”

Check with the fuel supplier to be sure you get the properly blended
fuel.

Handling of the fuel

Any fuel containing dust particles or water might cause engine failure.

Therefore, the following must be observed:

Take care to protect the fuel from ingress of dust particles or water
when filling the fuel tank.

If refuelling is done from an oil drum directly, ensure that it has been
kept stationary to allow any dust, sediment or water to settle at the
bottom.  Do  not  draw  fuel  direct  from  the  bottom  of  the  drum  to
prevent pick-up of any settled foreign material.

Always fully fill the fuel tank. Drain the sedimented particles in the
fuel tank frequently.

Water in fuel

During refuelling, it is possible for water (and other contaminants) to be
pumped into your fuel tank along with the diesel fuel. This can happen
if a fuel provider does not regularly inspect and clean its fuel tanks, or
receives contaminated fuel from its supplier(s). To protect your engine
from contaminated fuel, there is a fuel filter system on the engine which
allows you to drain excess water.

Be sure you do not overfill the fuel tank. Heat (such as from the engine)
can cause the fuel to expand. If the tank is too full, fuel could be forced
out.  This  could  lead  to  a  fire  and  the  risk  of  personal  injury  and/or
equipment damage.

Biocides

In warm or humid weather, fungus and/or bacteria may form in diesel
fuel if there is water in the fuel.

If  fungus  or  bacteria  has  caused  fuel  system  problems,  you  should
have  your  authorized  dealer  correct  these  problems.  Then,  use  a
diesel  fuel  biocide  to  sterilize  the  fuel  system  (follow  the  biocide
manufacturer‘s instructions). Biocides are available from your dealer,
service stations, parts  stores and other automotive places. See your
authorized  dealer  for  advice  on  using  biocides  in  your  area  and  for
recommendations on which biocides you should use.

Smoke suppressants

The use of a smoke suppressant additive is not allowed because of the
greater  possibility  of  stuck  rings  and  valve  failure,  resulting  from
excessive ash deposits.

Applicable Standard

Recommendation

JIS (Japanese Industrial Standard)

NO. 2

DIN (DEUTSCHE INDUSTRIE NORMEN)

DIN 51601

SAE (Society of Automotive Engineers) Based 
on SAE-J-313C

NO. 2-D

BS (BRITISH STANDARD) Based on BS/
2869-1970

Class A-1

EURONORM

EN590

NOTE: The fuel injection pump, injector or other parts of the fuel
system and engine can be damaged if you use any fuel or fuel
additive other than those specifically recommended by Doosan.

NOTE: If any  fuel other than  the one specified is used, engine
operation  will  be  impaired.  Engine  failure  or  malfunction
resulting from use of such improper fuel will not be warranted
by Doosan.

NOTE: Do  not  use  home heating oil  or  gasoline in your diesel
engine; either may cause engine damage.

NOTE: The water/diesel fuel mixture is flammable, and could be
hot.  To  avoid  personal  injury  and/or  property  damage,  do  not
touch the fuel coming from the drain valve, and do not expose
the fuel to open flames or sparks.

NOTE:  Fungus  or  bacteria  can  cause  fuel  system  damage  by
plugging  the  fuel  lines,  fuel  filters  or  injector.  They  can  also
cause fuel system corrosion.

Содержание 10/215HA





































































Отзывы: