background image

16

OPERATING INSTRUCTIONS

9/235HA, 10/215HA

STARTING THE MACHINE

All  normal  starting  functions  are  incorporated  in  the  key  operated
switch.

1. Turn the key switch to position (1). The engine fault and compressor

fault lamps will flash.

2. Turn the key switch to crank position (3) (engine start position)

3. Release to position (1) when engine starts. The engine will now be

running at a reduced speed.

At  temperatures  below 32°F (0°C)  or  if there  is difficulty starting first
time:

1. Open the manual blowdown valve fully.

2. Complete starting sequence above.

3. Close manual blowdown valve as soon as engine runs freely.

Do not  allow machine to  run for long periods with  manual blowdown
valve open.

4. Allow the engine to reach operating temperature.

5. At this point in the operation of the machine it is safe to apply full

load to the engine.

PUSH AFTER WARM-UP

Allow the engine to reach its operating temperature and then press the
button.

At this point in the operation of the machine it is safe to apply full load
to the engine.

DUAL PRESSURE REGULATION (WHEN FITTED)

Machines which operate in excess of 7 bar (100 psi) can optionally be
fitted  with  a  dual  pressure  switch  inside  the  unit.  This  switch  selects
between 7 bar (100 psi) and the machine rated pressure, cfm remains
nominally constant.

Starting  and  stopping  are  unaffected  by  the  selection  and  during
normal  running  the  selector  switch  may  be  safely  operated.
Precautions  must  be  taken  to  ensure  that  downstream  equipment  is
rated to suit the available pressure.

The pressure gauge indicates which setting has been selected.

STOPPING THE MACHINE

1. Close the service valve.

2. Allow  the  machine  to  run  unloaded  for  a  short  period  of  time  to

reduce the engine temperature.

3. Turn the start switch to the off position (0).

If the automatic blowdown valve fails to operate, then pressure must be
relieved from the system by means of the service valve(s).

EMERGENCY STOPPING

In the event that the unit has to be stopped in an emergency, TURN
THE  KEY  SWITCH  LOCATED  ON  THE  INSTRUMENT  PANEL  TO
THE 

OFF POSITION (0), or push the EMERGENCY STOP SWITCH

(when fitted).

RE-STARTING AFTER AN EMERGENCY

If  the  machine  has  been  switched  off  because  of  a  machine
malfunction, then identify and correct the fault before attempting to re-
start.

If the machine has been switched off for reasons of safety, then ensure
that the machine can be operated safely before re-starting.

Refer  to  the  PRIOR  TO  STARTING  and  STARTING  THE  UNIT
instructions earlier in this section before re-starting the machine.

MONITORING DURING OPERATION

Should any of the safety shut-down conditions occur, the unit will stop. 

Refer  to  the  diagnostic  display  page  for  a  listing  of  shutdown
conditions.

DECOMMISSIONING

When  the  machine  is  to  be  permanently  decommissioned  or
dismantled,  it  is  important  to  ensure  that  all  hazard  risks  are  either
eliminated or notified to the recipient of the machine. In particular:

Do  not  destroy  batteries  or  components  containing  asbestos
without containing the materials safely.

 Do not dispose of any pressure vessel that is not clearly marked
with  its  relevant  data  plate  information  or  rendered  unusable  by
drilling, cutting etc.

Do not allow lubricants or coolants to be released into land surfaces
or drains. 

Do  not  dispose  of  a  complete  machine  without  documentation
relating to instructions for its use.

NOTE: Position (2) not used on this model. Pre-heaters or glow
plugs are not fitted on this model.

NOTE: Wear hearing protection at all times when the engine is
started with the manual blowdown valve open and air is flowing
from the valve.

NOTE: In order to allow the machine to start at a reduced load, a
valve, which is operated by a button located on the instrument
panel,  is  incorporated  in  the  regulation  system.  (The  valve
automatically returns to the start position when the machine is
switched off and air pressure relieved from the system).

NOTE:  As  soon  as  the  engine  stops,  the  automatic  blowdown
valve will relieve all pressure from the system.

CAUTION: Never allow the machine to stand idle with pressure
in the system.

CAUTION: To ensure an adequate flow of oil to the compressor
at  low  temperature,  never  allow  the  discharge  pressure  to  fall
below 3,5 bar (50 psi).

Содержание 10/215HA





































































Отзывы: