background image

38

Donaldson Company, Inc.

Magnehelic

®

 Gauge 

The Magnehelic is a differential pressure gauge used to measure the pressure difference between the clean-air and dirty-air 

plenums and provides a visual display of filter change requirements. The high-pressure tap is located in the dirty-air plenum and 

the low-pressure tap is located in the clean-air plenum.
1.  Choose a convenient, accessible location on or near the collector for mounting that provides the best visual advantage.
2.  Plug the pressure ports on the back of the gauge using two, 1/8-in NPT pipe plugs supplied. Install two, 1/8-in NPT male 

adapters supplied with the gauge into the high- and low-pressure ports on the side of the gauges.

3.  Attach the mounting bracket using three, #6-32 x 1/4-in screws supplied.
4.  Mount the gauge and bracket assembly to the supporting structure using two, self-drilling screws.

5.  Thirty-five feet of plastic tubing is supplied and must be cut in two sections. Connect one section of tubing from the gauge’s 

high-pressure port to the pressure fitting located in the dirty-air plenum. Connect remaining tubing from the gauge’s low-

pressure port to the fitting in the clean-air plenum. Additional tubing can be ordered from your representative.

6.  Zero and maintain the gauge as directed in the manufacturer’s Operating and Maintenance Instructions provided.

Magnehelic Gauge Installation

clean-air plenum 

pressure tap location

flat washer

coupling

support structure

mounting surface

mounting screws

mounting bracket

static pressure tee

 90° elbow

adapter

adapter

flat washer

dirty-air plenum pressure tap location

adapter

90° male elbow

two, self-drilling screws

two, pipe plugs

plastic tubing

two adapters

low-pressure port

high-pressure port

Magnehelic gauge

90° male elbow

Содержание RP Baghouse

















































Отзывы: