Domel AZ 108 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 50

Domel AZ 108 Скачать руководство пользователя страница 40

AZ motor

Edition 4

Instructions for bearings replacement

40

MOTORS AZ 108, AZ 150, AZ 220

MOTOR AZ 84

Step 23: Installing the new rear bearing

You will need assembly paste (n), new bearing, adjusted press ring (o) and screw M4x30 or
M6x35 for this step.

Ensure that the bearing seat on the shaft is without any dirtiness or
mechanical particles.

The  bearing  has  to  be  new,  according  to  the  manufacturer's
specifications.

The force for the bearing installation has to be equable and it has to
act  on  the  inner  and  outer  ring  of  the  bearing  at  the  same  time.
Permissible forces for rear bearing installation are described in table
9. The bearing seat is designed to mount the rear bearing manually.
If manual rear bearing installation is not possible, use e.g. adjusted
press ring and  M6  screw  (motors AZ  84,  AZ 150 and  AZ  220)  or
M4 screw  (motor  AZ 108)  and slowly screw  the screw  into thread
in  the  shaft  to  get  the  right  position  of  bearing.  See  picture  B  for
additional information.

When done remove the adjusted press ring and screw.

The  installation  of  rear  bearing  must  be  done  exactly  in  the
direction of the axis.
Ensure  that  the  bearing  is  installed  up  to  the  level  on  the  shaft
(bearing  seat).  Otherwise  the  distances  between  the  components
will  not  be  appropriate.  Because  of  that  the  bearing  will  be

16 (torx T30)

«
...
38
39
40
41
42
...
»

Содержание AZ 108



















































Отзывы:

Нет отзывов