Domel AZ 108 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 50

Domel AZ 108 Скачать руководство пользователя страница 33

AZ motor

Edition 4

Instructions for bearings replacement

33

Bearing must not be heated over 110°C because higher temperature
influence bearing grease which can lead to shorter bearing life time.

Ensure  that  the  bearing  is  installed  up  to  the  level  on  the  shaft
(bearing  seat).  Otherwise  the  distances  between  the  components
will  not  be  appropriate.  Because  of  that  the  bearing  will  be
overloaded  which  lead  to  shorter  life  time  or  the  assembly  of  the
motor will not be possible.

Appropriate  support  for  bearing  installation  is  just  shaft  end.  You
cannot support rotor on the rotor ring because forces during bearing
installation can influence the magnets and rotor ring which can lead
to rotor damages and shorter motor life time.

RISK OF INJURY.
In case of installation of the bearing with preliminary heating be
careful not to burn your hands because bearing surface is hot.

Do not use any other kind of bearing heating except the inductive
heater.

Place rotor with shaft on a flat, soft and clean surface. Remove any tape or parallel key if you
placed it on a shaft in previous step. Ensure that the bearing seat on the shaft is without any
dirtiness or mechanical particles. Install the new bearing.

FORCE ON
INNER RING

FORCE ON
INNER RING

SUPPORT DURING
BEARING INSTALLATION

«
...
31
32
33
34
35
...
»

Содержание AZ 108



















































Отзывы:

Нет отзывов