Domel AZ 108 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 50

Domel AZ 108 Скачать руководство пользователя страница 34

AZ motor

Edition 4

Instructions for bearings replacement

34

Step 17: Lubricating and installing rotor with shaft back into flange

You will need assembly grease (n) for this step.

Be careful not to damage the motor shaft.

Be  careful  not  to  assemble  rotor  with  shaft  suddenly  because  the
strike could damage the new bearing and magnets.

The installation of the rotor must be done exactly in the direction of
the axis.

Assembly  paste  is  used  to  prevent  the  corrosion  between  two
materials  (between  bearing  and  bearing  seat  in  the  flange)  and  to
ensure easy assembly (O-ring lubrication in the flange).

Please ensure  that front bearing  is  fully placed  into  bearing seat in
flange.

Avoid touching the rotor magnets.

Before installation ensure that front bearing is cooled down on a room temperature (if you
heated it in previous step). You must also lubricate bearing seat and O-ring in the flange with
assembly paste. Apply only a thin layer of assembly paste. Make sure that O-ring is in correct
position in bearing seat groove.

Place rotor with shaft into flange slowly to the end position.

MOTORS AZ 108, AZ 150, AZ 220

MOTOR AZ 84

«
...
32
33
34
35
36
...
»

Содержание AZ 108



















































Отзывы:

Нет отзывов