background image

 

domat UI0xx 

10/2017 Subject to technical changes. 

UI075 

 

 

 

 

 

 

 
Units without knobs are used as indicators, optionally with remote controlled inputs / 
outputs. Process control algorithms (activating of the outputs by increased / decreased 
temperature, humidity etc.) must be implemented in a master controller.  
 

Installation 
 

Units are intended for operating in ordinary and chemically non-aggressive environment. 
They  do  not  need  any  servicing  or  maintenance.  Install  them  in  a  vertical  position  at 
places where they can be operated easily and measure correct values of temperature and 
humidity, i.e. in the height of about 150 cm, with no direct sunlight or other source heat 
or cold (AHU outlets, refrigerator, electrical appliances). The device consists of two parts: 
bottom with screw terminal block and top cover containing PCB, display, and the knob. 
The bottom part is fixed by 2 or 4 screws to any flat surface or a flush-

mounting box Ø 50 

mm. There is an aperture for cabling in the back of the bottom part. The bottom should 
be  installed  and  cabling  connected  first,  and  the  upper  part  inserted  after  the 
construction works have been finished to prevent damage to the unit. 

 

Seal the conduits to avoid influencing the sensor by draught. Use insulating pad when 
installing the sensor on cold walls. Avoid sensor exposition to sunlight or other sources 
of heat. 
 

 

 

Opening the 
cover 
 

When removing the display part, proceed as follows: 
 

-

 

press gently the side parts of the unit and pull the right of the display part by 
several milimeters 

-

 

pull the left of the display part 

-

 

pull the display part and remove it from the bottom. 

 
Do not bend the display part too much, the connector pins could be damaged. The locks 
are only at the sides of the display part, not at the top nor bottom. 

Содержание UI0 Series









Отзывы: