In
Non-contact
Infrared
Thermometer
function
(IRT
Mode)
#
The
laser
will
automatically
turns
on
while
the
Scan
button
is
pressed.
While scanning, the newest temperature will be updated on the LCD and the measurement will continue as long as
the Meas.(infrared) key is depressed. When the Meas.(infrared) key is released, icon “Hold” will appear on the display
and the last measurement will remain visible for 15 seconds before the display goes blank.
CAUTION
1.
WHEN
DEVICE
IS
IN
USE,
DO
NOT
LOOK
DIRECTLY
INTO
THE
LASER
BEAM–PERMANENT
EYE
DAMAGE
MAY
RESULT.
2.
USE
EXTREME
CAUTION
WHEN
OPERATING
THE
LASER.
3.
NEVER
POINT
THE
DEVICE
TOWARDS
ANYONE’S
EYES.
4.
KEEP
OUT
OF
REACH
OF
ALL
CHILDREN.
Mode
Selection
MIN
MAX
LOCK
o
C/
o
F
EMIS
MINIMUM
OR
MAXIMUM
MODE
The thermometer will display the minimum or maximum reading during the measurement period only until the Mode
key is pressed.
To utilize the minimum mode, please press Meas.(infrared) key
Mode key
Meas.(infrared) key. And keep
pressing Meas.(infrared) key for measurement.
To utilize the maximum mode, please press Meas.(infrared) key
Mode key *twice
Meas.(infrared) key. And keep
pressing Meas.(infrared) key for measurement.
LOCK
MODE
The lock mode is particularly useful for continuous monitoring of temperatures. The thermometer will continuously
display the temperature for up to 60 minutes or until the Meas.(infrared) key button is pressed.
To utilize the lock mode, please press Meas.(infrared) key
Mode key *three times
Meas.(infrared) key.
o
C
OR
o
F
MODE
To change the ‘
o
C’ or ‘
o
F’ mode, please press Meas.(infrared) key
Mode key *four times
Meas.(infrared) key.
Same steps can be taken when switching from
o
F to
o
C.
EMISSIVITY
The infrared thermometer is supplied with a default emissivity of 0.95. The emissivity can be changed from 0.10 (10E)
to 1 (100E). Changes should only be carried out by experienced personnel. For information relating to the emissivity
of specific materials, please contact the nearest retailer. Note: non-contact infrared thermometers are not
recommended for use in measuring the temperature of shiny or polished metals.
To change the emissivity, please Meas.(infrared) key
Mode key *five times
Meas.(infrared) key for each 0.01
(1E) adjustment
Mode key.
In
Contact
Thermocouple
Probe
function
(COT
Mode)
Connect the thermocouple with Thermocouple socket and put the probe in/on the target. Press Scan key to
continuously display the temperature for up to 4 minutes. After that the device will automatically shut off to extend the
battery life. Press Scan key will interrupt the scanning to display the last temperature with a 'Hold' wording. To reenter
scanning just press Scan key again.
After measure high temp, the probe may remain HOT for a while.
The
measure
range
is
for
thermometer
only.
User
should
choose
proper
probe
types
for
different
kinds
of
application.
Please
make
sure
the
target
to
be
measured
will
not
exceed
the
temperature
range
of
the
probe
to
avoid
permanent
damage
of
the
thermocouple
probe.
To
avoid
electric
shock
and
thermometer
damage,
do
not
measure
live
circuit
where
voltage
exceeding
24V
AC
RMS
or
60V
DC
with
the
thermocouple
probe.
STORAGE
&
CLEANING
It should be stored at room temperature. The sensor lens is the most delicate part of the thermometer. The lens
should be kept clean at all times, care should be taken when cleaning the lens using only a soft cloth or cotton swab
with water or medical alcohol, allowing the lens to fully dry before using the thermometer. Do not submerge any part
of the thermometer.
LCD
ERROR
MESSAGES
The thermometer incorporates visual diagnostic messages as follows:
‘Hi’ or ’Lo’ is displayed when the temperature being measured is outside of the
「
」
「
」
measurement range.
view
Emissivity = 0.1~1 Step.01
Distance:Spot (FOV)= 12:1
Simply aim the thermometer at the measure target with “Infrared Lens” and
press Meas.(infrared) key to display the surface temperature. The distance
Wave Length = 8um-14um
to target ratio is 12:1.Please make sure the target size is within the field of
HACCP
check
The “HACCP CHECK” feature is incorporated in our thermometer
temperature to graphically indicate critical temperature zone. The icons
and LED indicators located above the display indicate a food product
stays in a safe or unsafe HACCP “ Danger Zone” temperature. The
green and red LED light will always be lit before power off.
A Green LED appears with icon ”
” indicates a safe cool or frozen
condition below 4
o
C(40
o
F) or appears with icon ”
” indicates a safe
holding temperature above 60
o
C(140
o
F).
When temperature is between 4
o
C and 60
o
C, the red LED with icon ”
” will appear and indicate that the temperature is fallen within the HACCP “Danger Zone” from 4
o
C to 60
o
C
(40~140
o
F)
.
FI51P Thermometer
Operating
Instructions
The thermometer is a non-contact infrared thermometer, also with Probe thermometer. You can
select only one Mode at the same time but can change the Mode at will. Please remember to keep
away from baby and children and don’t use it for safety related applications.
