Dodge Neon 2001, Руководство по обслуживанию

Страница: 731 / 743

(4) Pull HVAC control head out of instrument
panel, twist 90° and position in place (Fig. 3).
(5) Connect the one vacuum harness connector.
(6) Connect the one instrument panel wire harness
connector.
(7) Install the two retaining screws to the HVAC
control head.
(8) Install the center A/C duct through the opening
in the instrument panel, making sure it snaps down
over the mating duct on the A/C unit. Tabs on each
side will guide into slots in instrument panel.
(9) Position the center bezel and firmly snap into
place.
(10) Install the two screws retaining the top front
of the center bezel.
(11) Snap in the A/C outlet barrels.
(12) Firmly push on the HVAC control head knobs.
(13) Connect one left side harness connector at top
left of instrument panel for vanity and rear view mir-
rors.
(14) Connect two harness connectors to HVAC at
right top instrument panel (Fig. 2).
(15) Install the left and right A-pillar door harness
connectors (Fig. 1).
(16) Connect the right side antenna connector.
(17) Install the left and right A-pillar mounting
bolts. First the lower bolt, then the upper bolt on
each side.
(18) Install the two center support mounting bolts.
(19) Install two bolts on top of the brake pedal
support bracket.
(20) Install the two cowl top instrument panel
retaining nuts (right side).
(21) Position the Data Link Connector (DLC) into
mounting slot and firmly snap into place in instru-
ment panel reinforcement.
(22) Install the center console. Refer to Body, Inte-
rior, Center Console, Installation.
(23) Install the left and right cowl side panels.
(24) Install the left and right instrument panel
end covers.
(25) Install the steering column. Refer to Steering,
Steering Column, Installation.
(26) Position the left lower instrument panel cover
over mounting slots and firmly snap into place.
Install the two screws on lower edge.
(27) Position the cluster bezel over mounting slots
and firmly snap into place.
(28) Install the instrument panel top cover. Refer
to Body, Instrument Panel, Instrument Panel Top
Cover, Installation.
(29) Position the left and right A-pillar trim mold-
ings over mounting slots and firmly snap into place.
(30) Install the door seal.
(31) Connect the battery negative cable.
INSTRUMENT PANEL END
COVER
REMOVAL
(1) The drivers end cover can be removed using
the handle. Using a trim stick (special tool #C-4755)
or equivalent, gently pry out on the right end cover
and remove. The fuse diagram is located inside the
left end cover. Fuse Access is under the left end
cover.
INSTALLATION
(1) Guide the end cover under the forward lip of
the door seal and position the end cover over the
mounting slots and firmly snap into place.
(2) Close door.
INSTRUMENT PANEL TOP
COVER
REMOVAL
(1) Loosen the two screws at each end off the
defroster slot until they are flush with top cover sur-
face (DO NOT REMOVE).
(2) Remove the screw at each end of the top cover.
(3) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out on both the left and right
A-pillar trim panels and remove.
(4) Use care not to scratch the panel. Lift up at
each end of the cluster bezel and along the rearward
edge of the top cover to disengage the clips.
(5) Pull the top cover rearward until the forward
pins disengage from the instrument panel.
INSTALLATION
(1) Push the top cover forward assuring that the
pins on the top cover engage the slots in the in the
instrument panel.
(2) Use care not to scratch the panel. Position the
top cover clips over their mounting slots and start
the retaining clips into each slot. Starting in the mid-
dle, firmly snap the top cover into place using a firm
blow with the hand at each clip position.
(3) Align the left and right A-pillar trim panels
over the mounting slots and firmly snap into place.
23s - 10 INSTRUMENT PANEL
PL
INSTRUMENT PANEL ASSEMBLY (Continued)
ProCarManuals.com
2001 NEON